Eddyfi Technologies
Swift MFL portable instrument with a large, premium-quality multi-touch display. Incl.2 batt., power supp., manual, rugged case.
SONYKS portable rugged GWT unit with 40 data channels. C/w large 10.4" multi-touch display, integrated pump. Incl. 2 batt., PSU, user manual and rugged case.
Amigo2 SE ACFM instrument with large multi-touch display. Supports legacy, SENSU and SENSU2 single element probes. Includes 2 batteries, AC PSU, test block and transport case. Requires Assist-GO-SE software subscription, sold separately.
Reddy Eddy Current Array is designed to meet the unique in-service needs of the oil & gas, power generation, and aerospace industries.
Swift UT portable unit. Incl. a premium-quality 26.4cm (10.4in) multi-touch display and high-capacity 100GB SSD. Software for B-Scan, integrated joystick, AC PS, 2x hot swap. Li-ion batt. w/ charger, manual & transport case. For Scorpion2 crawler.
Amigo2 inst. with a large multi-touch display. Supp. legacy, SENSU, SENSU2 probes and array. Includes 2 batt., AC PSU, test block and transp. case. Requires Assist GO software subscription, sold separately.
Reddy portable 64-ch. surface ECA instrument with a large, premium-quality multi-touch display. Very capable unit for surface ECA inspections . No MFL capabilities . Upgradable later to 128-channel, with or without MFL.
M2M MantisTM is a robust and lightweight flaw detector offering UT, PAUT, TOFD, and TFM through the streamlined user interface called CaptureTM. Based on a 16:64PR architecture with three different models, Mantis addresses both general and advanced applications without compromising productivity.
Silverwing Swift MFL Corrosion Mapping - NEW (SWIFT-M)
Swift MFL portable instrument with a large, premium-quality multi-touch display. Incl.2 batt., power supp., manual, rugged case.
Highlights :
SPECS :
Acquisition modes Internal Clk, Encoder
Array connectors 1x IPEX
Batteries - typical life 6-8 hours
Cooling Sealed with internal fan
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Full recordable data for mapping Yes
High temperature inspections Yes
Highly portable easy to use system Yes
Multitouch control Yes
Nb. of input channels 8
Nb. of receiving elements Up to 128
Paperless Reporting Yes
Precision active steering No
Probability of detection 2mm diameter 20% loss
Probe type MFL
Rapid Coverage Yes
Rope access applications Yes
Setup creation/management Yes
Umbilical length 5m, 10m and 15m
Acquisition rate Up to 50 kHz
Automatic screenshot with defect entry Yes
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance EN 61010-1, CE, WEEE, FCC, Part 15B, ICES-003, RoHS
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors 1x 12-pin Fischer
Inspection workflows Optimized, with hard buttons
MFL receiver gain 23 - 64 dB
Programmable alarms Yes
Recordable UT data sets Yes
RFT/NFT/MFL connector Yes
Harness available Yes
Full screen mode Yes
Connectivity Gigabit Ethernet, Wi-Fi, HDMI, USB 2.0 (x3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 3-axis Quadrature / Step /Dir, TTL 5V
IP rating IP65
Operating humidity 95%, non-condensing
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements Battery Operated
Programmable outputs Yes
Supported Technologies/Techniques MFL
Storage temperature 0°C to 40°C (32°F to 104°F)
Volume 13L (793.31 in3)
Weight (without batteries) 5.7 kg (12.5 lb)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
Highlights :
- Fast, reliable corrosion screening even in service
- Portable, battery-operated, sealed, large bright display
- Simple to learn and operate, offers a high PoD
SPECS :
Acquisition modes Internal Clk, Encoder
Array connectors 1x IPEX
Batteries - typical life 6-8 hours
Cooling Sealed with internal fan
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Full recordable data for mapping Yes
High temperature inspections Yes
Highly portable easy to use system Yes
Multitouch control Yes
Nb. of input channels 8
Nb. of receiving elements Up to 128
Paperless Reporting Yes
Precision active steering No
Probability of detection 2mm diameter 20% loss
Probe type MFL
Rapid Coverage Yes
Rope access applications Yes
Setup creation/management Yes
Umbilical length 5m, 10m and 15m
Acquisition rate Up to 50 kHz
Automatic screenshot with defect entry Yes
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance EN 61010-1, CE, WEEE, FCC, Part 15B, ICES-003, RoHS
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors 1x 12-pin Fischer
Inspection workflows Optimized, with hard buttons
MFL receiver gain 23 - 64 dB
Programmable alarms Yes
Recordable UT data sets Yes
RFT/NFT/MFL connector Yes
Harness available Yes
Full screen mode Yes
Connectivity Gigabit Ethernet, Wi-Fi, HDMI, USB 2.0 (x3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 3-axis Quadrature / Step /Dir, TTL 5V
IP rating IP65
Operating humidity 95%, non-condensing
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements Battery Operated
Programmable outputs Yes
Supported Technologies/Techniques MFL
Storage temperature 0°C to 40°C (32°F to 104°F)
Volume 13L (793.31 in3)
Weight (without batteries) 5.7 kg (12.5 lb)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
Swift MFL portable instrument with a large, premium-quality multi-touch display. Incl.2 batt., power supp., manual, rugged case.
SONYKS Portable GWT Instrument - NEW (SONYKS-GWT)
SONYKS portable rugged GWT unit with 40 data channels. C/w large 10.4" multi-touch display, integrated pump. Incl. 2 batt., PSU, user manual and rugged case.
Highlights :
SPECS :
Batteries - typical life 8-10 hours
Cooling Sealed and fanless
Data storage SSD, 256 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Nb. of transmit channels 40
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance IEC 61010-1, CE, UKCA, WEEE, FCC Part 15, ICES-001
Data readback on PC software Yes
Output voltage 200V peak to peak
Probe recognition and setup (ChipID) Automatic with Sonyks tooling including ring type, size, serial number, pipe and angular orientation
Harness available Yes
Automated self-check Onboard capacitance and resistance testing
Connectivity Gigabit Ethernet, Wi-Fi 6 (802.11ax), USB 2.0 (×3), HDMI
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Focussing options C-Scan imaging; Time delay focussing
GPS Accurate positioning to 2.5 m (8.2 ft)
Internal pump Yes
IP rating IP54
Laptop connectivity Yes
Maximum sample range 125ms (365m longitudinal mode; 200m torsional mode)
Max averaging 128
Nb. of receive channels 40
Onboard pump SSD, 256 GB
Receiver Gain Up to 100dB
Supported rings Sonyks Piezo and Magneto tools, Teletest and other commercial piezo-based rings
Supported Technologies/Techniques GWT, LRUT, MRUT
Storage Wi-Fi or Gigabit Ethernet
Transduction compatibility Magnetostrictive and Piezoelectric transducers
Weight (with batteries) 7.2kg (15.9 lb)
APPLICATIONS :
Corrosion Under Insulation (CUI) on insulated pipes and pipelines
High-speed, high-efficiency pipeline corrosion screening
Distribution, gathering, feeder or transmission pipelines
Pipeline integrity programs
Small diameter piping
Unpiggable pipes
Power plant pipelines
Buried pipeline inspection
Flanged pipes
River crossings
Road crossings
Drill riser inspection
Stainless steel pipe inspection
Chemical plant piping
Food piping
Highlights :
- First unit with full onboard screen for GWT; top efficiency
- Unmatched signal-to-noise ratio with broadband and FMC
- Support non-Eddyfi rings; also Magneto-strictive collars
SPECS :
Batteries - typical life 8-10 hours
Cooling Sealed and fanless
Data storage SSD, 256 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Nb. of transmit channels 40
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance IEC 61010-1, CE, UKCA, WEEE, FCC Part 15, ICES-001
Data readback on PC software Yes
Output voltage 200V peak to peak
Probe recognition and setup (ChipID) Automatic with Sonyks tooling including ring type, size, serial number, pipe and angular orientation
Harness available Yes
Automated self-check Onboard capacitance and resistance testing
Connectivity Gigabit Ethernet, Wi-Fi 6 (802.11ax), USB 2.0 (×3), HDMI
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Focussing options C-Scan imaging; Time delay focussing
GPS Accurate positioning to 2.5 m (8.2 ft)
Internal pump Yes
IP rating IP54
Laptop connectivity Yes
Maximum sample range 125ms (365m longitudinal mode; 200m torsional mode)
Max averaging 128
Nb. of receive channels 40
Onboard pump SSD, 256 GB
Receiver Gain Up to 100dB
Supported rings Sonyks Piezo and Magneto tools, Teletest and other commercial piezo-based rings
Supported Technologies/Techniques GWT, LRUT, MRUT
Storage Wi-Fi or Gigabit Ethernet
Transduction compatibility Magnetostrictive and Piezoelectric transducers
Weight (with batteries) 7.2kg (15.9 lb)
APPLICATIONS :
Corrosion Under Insulation (CUI) on insulated pipes and pipelines
High-speed, high-efficiency pipeline corrosion screening
Distribution, gathering, feeder or transmission pipelines
Pipeline integrity programs
Small diameter piping
Unpiggable pipes
Power plant pipelines
Buried pipeline inspection
Flanged pipes
River crossings
Road crossings
Drill riser inspection
Stainless steel pipe inspection
Chemical plant piping
Food piping
SONYKS portable rugged GWT unit with 40 data channels. C/w large 10.4" multi-touch display, integrated pump. Incl. 2 batt., PSU, user manual and rugged case.
TSC Amigo2 SE ACFM system - NEW (Amigo2 SE ACFM system)
Amigo2 SE ACFM instrument with large multi-touch display. Supports legacy, SENSU and SENSU2 single element probes. Includes 2 batteries, AC PSU, test block and transport case. Requires Assist-GO-SE software subscription, sold separately.
Highlights :
SPECS :
ACFM connectors 1x Sensu 2,1x Sensu,1x Legacy
ACFM frequency 5 KHz, 50 KHz
Acquisition modes Clock, Encoded
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Critical Zone Inspection (Curved Scaning) Yes
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
High temperature inspections Yes
Highly portable easy to use system Yes
Multitouch control Yes
Paperless Reporting Yes
Rapid Coverage Yes
Remote control availability Yes
Rope access applications Yes
Automatic screenshot with defect entry Yes
Batteries - type 2x li-ion, rechargeable, DOT compliant
Communications Ethernet
Compliance ASME, EN 61010-1, CE, WEEE, FCC Part 15B, ICES-003, AS/NZS CISPR 22, RoHS
Data readback on PC software Yes
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors Fischer DBPU 1031 A012–130
Inspection workflows Yes
Optional PC software available Yes
Probe recognition and setup (ChipID) Yes
Support custom application and probes Yes
Harness available Yes
Connectivity Gigabit Ethernet, Wi-Fi, Dual Mode Bluetooth® 2.1, 2.1 EDR, 3.0, 3.0 HS, 4.0 (BLE), USB 2.0 (×3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 2 inputs, quadrature
IP rating IP65
Operating humidity 95%, non-condensing
Operating temperature -10° to 45°C (14 to 113°F)
Power supply/requirements 100–240 VAC ± 10% 50–60 Hz
Supported Technologies/Techniques ACFM
Storage temperature -20°C to 60°C (-4°F to 140°F)
Volume 13L (793.31 in3)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
APPLICATIONS :
Highlights :
- Detect and size surface cracks through paint and coatings
- Portable, battery-operated, sealed, large bright display
- Single element with support of previous-gen / legacy probes
SPECS :
ACFM connectors 1x Sensu 2,1x Sensu,1x Legacy
ACFM frequency 5 KHz, 50 KHz
Acquisition modes Clock, Encoded
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Critical Zone Inspection (Curved Scaning) Yes
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
High temperature inspections Yes
Highly portable easy to use system Yes
Multitouch control Yes
Paperless Reporting Yes
Rapid Coverage Yes
Remote control availability Yes
Rope access applications Yes
Automatic screenshot with defect entry Yes
Batteries - type 2x li-ion, rechargeable, DOT compliant
Communications Ethernet
Compliance ASME, EN 61010-1, CE, WEEE, FCC Part 15B, ICES-003, AS/NZS CISPR 22, RoHS
Data readback on PC software Yes
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors Fischer DBPU 1031 A012–130
Inspection workflows Yes
Optional PC software available Yes
Probe recognition and setup (ChipID) Yes
Support custom application and probes Yes
Harness available Yes
Connectivity Gigabit Ethernet, Wi-Fi, Dual Mode Bluetooth® 2.1, 2.1 EDR, 3.0, 3.0 HS, 4.0 (BLE), USB 2.0 (×3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 2 inputs, quadrature
IP rating IP65
Operating humidity 95%, non-condensing
Operating temperature -10° to 45°C (14 to 113°F)
Power supply/requirements 100–240 VAC ± 10% 50–60 Hz
Supported Technologies/Techniques ACFM
Storage temperature -20°C to 60°C (-4°F to 140°F)
Volume 13L (793.31 in3)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
APPLICATIONS :
- Weld inspection: with standard probes and single-pass array probes
- One or two-person operation (e.g. confined spaces)
- High-temperature applications
- Inspection through thick coatings
- Thread inspection
- Underwater inspection
Amigo2 SE ACFM instrument with large multi-touch display. Supports legacy, SENSU and SENSU2 single element probes. Includes 2 batteries, AC PSU, test block and transport case. Requires Assist-GO-SE software subscription, sold separately.
Reddy with 32-channel Eddy Current Array - NEW (Reddy 32 Channel)
Reddy Eddy Current Array is designed to meet the unique in-service needs of the oil & gas, power generation, and aerospace industries.
Intuitive Real-Time C-Scan Imaging
High-quality C-scans convey a wealth of information. Analyzing eddy current signals is much more intuitive thanks to on-the-fly 2D imaging.
Massive Multi-Touch Display
The premium-quality 26.4 cm (10.4 in) LED display is optically bonded, non-reflective, and comes with 3 mm (1/8 in) strengthened glass. It’s
designed for gloved hands, under any lighting conditions. The multi-touch capabilities enable easily zooming and rotating views.
The Power of Eddy Current Array
The state-of-the-art electronics of Reddy offer up to 128 built-in SmartMUX™ channels, allowing for high-resolution, single-pass scans
with wider coverage. Surface ECA with Reddy means a high probability of detection and significantly faster inspections.
Designed for Field Use
Sealed and designed for IP65. The magnesium alloy casing is tough, water and dust resistant, and cools without any external air exchange. The adjustable stand, the top handle, and four corner anchor points make it practical for on-site inspections.
Modern PC Capabilities
Equipped with a robust, 100 GB internal solid-state disk drive (SSD) for secure inspection data. The embedded, portable Windows® PC offers
standard connect-anywhere capabilities and advanced productivity tools that optimize field testing.
SPECS :
Array connectors 1x 160 pin
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Highly portable easy to use system Yes
Multitouch control Yes
Nb. of array channels 32
Nb. of input channels 8
Probability of detection High
Rope access applications Yes
Setup creation/management Setup wizards
Acquisition rate Up to 50 000 samples/sec
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance ASME, EN 61010-1, CE, WEEE, FCC Part 15B, ICES-003, AS/NZS CISPR 22, RoHS
Data readback on PC software Yes
ECA frequency range 5 Hz - 10 MHz
ECA multiplexer SmartMUX
ECT connectors 1X 19-pin Fischer
ECT frequency range 5 Hz - 10 MHz
ECT simultaneous frequency Up to 160
Encoders and I/O connectors 12-pin Fischer
Frequency range 5 Hz–10 MHz
Inspection workflows Optimized, with hard buttons
Input impedance 50 or 100 Ohms
Injection modes Multiplexed, simultaneous, continuous
Optional PC software available Yes
Output voltage Up to 20 Vpp
Probe recognition and setup (ChipID) Automatic
Support custom application and probes Yes
Synchronization with I/O Yes
Harness available Yes
Connectivity Gigabit Ethernet, Wi-Fi, Dual Mode Bluetooth® 2.1, 2.1 EDR, 3.0, 3.0 HS, 4.0 (BLE), USB 2.0 (×3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 2 axes, quadrature
IP rating Designed for IP65
Operating humidity 95%, non-condensing
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements Direct VAC or onboard batteries
Supported Technologies/Techniques ECT, ECA
Volume 13L (793.31 in3)
Weight (without batteries) 5.7 kg (12.5 lb)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
APPLICATIONS :
Intuitive Real-Time C-Scan Imaging
High-quality C-scans convey a wealth of information. Analyzing eddy current signals is much more intuitive thanks to on-the-fly 2D imaging.
Massive Multi-Touch Display
The premium-quality 26.4 cm (10.4 in) LED display is optically bonded, non-reflective, and comes with 3 mm (1/8 in) strengthened glass. It’s
designed for gloved hands, under any lighting conditions. The multi-touch capabilities enable easily zooming and rotating views.
The Power of Eddy Current Array
The state-of-the-art electronics of Reddy offer up to 128 built-in SmartMUX™ channels, allowing for high-resolution, single-pass scans
with wider coverage. Surface ECA with Reddy means a high probability of detection and significantly faster inspections.
Designed for Field Use
Sealed and designed for IP65. The magnesium alloy casing is tough, water and dust resistant, and cools without any external air exchange. The adjustable stand, the top handle, and four corner anchor points make it practical for on-site inspections.
Modern PC Capabilities
Equipped with a robust, 100 GB internal solid-state disk drive (SSD) for secure inspection data. The embedded, portable Windows® PC offers
standard connect-anywhere capabilities and advanced productivity tools that optimize field testing.
SPECS :
Array connectors 1x 160 pin
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Highly portable easy to use system Yes
Multitouch control Yes
Nb. of array channels 32
Nb. of input channels 8
Probability of detection High
Rope access applications Yes
Setup creation/management Setup wizards
Acquisition rate Up to 50 000 samples/sec
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance ASME, EN 61010-1, CE, WEEE, FCC Part 15B, ICES-003, AS/NZS CISPR 22, RoHS
Data readback on PC software Yes
ECA frequency range 5 Hz - 10 MHz
ECA multiplexer SmartMUX
ECT connectors 1X 19-pin Fischer
ECT frequency range 5 Hz - 10 MHz
ECT simultaneous frequency Up to 160
Encoders and I/O connectors 12-pin Fischer
Frequency range 5 Hz–10 MHz
Inspection workflows Optimized, with hard buttons
Input impedance 50 or 100 Ohms
Injection modes Multiplexed, simultaneous, continuous
Optional PC software available Yes
Output voltage Up to 20 Vpp
Probe recognition and setup (ChipID) Automatic
Support custom application and probes Yes
Synchronization with I/O Yes
Harness available Yes
Connectivity Gigabit Ethernet, Wi-Fi, Dual Mode Bluetooth® 2.1, 2.1 EDR, 3.0, 3.0 HS, 4.0 (BLE), USB 2.0 (×3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 2 axes, quadrature
IP rating Designed for IP65
Operating humidity 95%, non-condensing
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements Direct VAC or onboard batteries
Supported Technologies/Techniques ECT, ECA
Volume 13L (793.31 in3)
Weight (without batteries) 5.7 kg (12.5 lb)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
APPLICATIONS :
Depending on the instrument configuration:
- Corrosion on ferromagnetic pipes, tank walls and more
- Detecting and sizing cracks in stainless steel welds
- Detecting and assessing stress corrosion cracking
- Butt weld and fillet weld inspection for cracking and surface discontinuities
- Faster, less operator-dependant, surface inspection compared to PT/MT
- Assessing corrosion on aluminum and stainless steel tank floors
- Gear inspection
- Pipeline integrity
Reddy Eddy Current Array is designed to meet the unique in-service needs of the oil & gas, power generation, and aerospace industries.
Silverwing Swift UT Corrosion Mapping - NEW (Silverwing Swift UT)
Swift™ UT portable unit. Incl. a premium-quality 26.4cm (10.4in) multi-touch display and high-capacity 100GB SSD. Software for B-Scan, integrated joystick, AC PS, 2x hot swap. Li-ion batt. w/ charger, manual & transport case. For Scorpion2 crawler.
Highlights :
SPECS :
Acquisition modes Encoded
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Full recordable data for mapping Yes
Highly portable easy to use system Yes
Multitouch control Yes
Nb. of input channels 1
Nb. of channels 2
Nb. of receiving elements 1
Paperless Reporting Yes
Precision active steering Yes
Probe type Dry coupled UT for quick and easy setup
Pulser (UT) voltage From 25 V to 200 V (with 25 V steps)
Rapid Coverage Yes
Remote control availability Yes
Rope access applications Yes
Setup creation/management Yes
Shockproof rating According to MIL-STD-810G
Umbilical length 50 m (164 ft)
Acquisition rate Up to 20 kHz (currently software limited to 200 Hz)
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance CE, ICES, FCC
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors 18 Pin lemo proprietary Pinout
Frequency range 2.25 MHz to 20 MHz
Gain range (UT-TOFD) Up to 70 dB (1 dB steps)
Gates Yes
Inspection workflows Optimized, with hard buttons
Output voltage 15V / 100W
Probe recognition and setup (ChipID) No
Pulse type (UT-TOFD) Pulse-Echo, pitch and catch
Pulse width 25-225ns, 2.5ns increments
Recordable UT data sets Yes
UT connectors 2x LEMO 00
Harness available Yes
Full screen mode Yes
Connectivity Gigabit Ethernet, Wi-Fi, USB 2.0 (x4)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
External trigger No
Encoder inputs 2 axes, quadrature
IP rating IP65
Operating humidity 95%, non-condensing
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements Battery Operated
Programmable outputs Yes
Supported Technologies/Techniques UT
Storage temperature 0°C to 40°C (32°F to 104°F)
Volume 13L (793.31 in3)
Weight (without batteries) 5.7 kg (12.5 lb)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
Highlights :
- Fast, reliable ultrasonic tank shell/roof inspections
- Portable, battery-operated, sealed, large bright display
- Dry-coupled UT probe offers a high PoD Vs. spot checks
SPECS :
Acquisition modes Encoded
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Full recordable data for mapping Yes
Highly portable easy to use system Yes
Multitouch control Yes
Nb. of input channels 1
Nb. of channels 2
Nb. of receiving elements 1
Paperless Reporting Yes
Precision active steering Yes
Probe type Dry coupled UT for quick and easy setup
Pulser (UT) voltage From 25 V to 200 V (with 25 V steps)
Rapid Coverage Yes
Remote control availability Yes
Rope access applications Yes
Setup creation/management Yes
Shockproof rating According to MIL-STD-810G
Umbilical length 50 m (164 ft)
Acquisition rate Up to 20 kHz (currently software limited to 200 Hz)
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance CE, ICES, FCC
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors 18 Pin lemo proprietary Pinout
Frequency range 2.25 MHz to 20 MHz
Gain range (UT-TOFD) Up to 70 dB (1 dB steps)
Gates Yes
Inspection workflows Optimized, with hard buttons
Output voltage 15V / 100W
Probe recognition and setup (ChipID) No
Pulse type (UT-TOFD) Pulse-Echo, pitch and catch
Pulse width 25-225ns, 2.5ns increments
Recordable UT data sets Yes
UT connectors 2x LEMO 00
Harness available Yes
Full screen mode Yes
Connectivity Gigabit Ethernet, Wi-Fi, USB 2.0 (x4)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
External trigger No
Encoder inputs 2 axes, quadrature
IP rating IP65
Operating humidity 95%, non-condensing
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements Battery Operated
Programmable outputs Yes
Supported Technologies/Techniques UT
Storage temperature 0°C to 40°C (32°F to 104°F)
Volume 13L (793.31 in3)
Weight (without batteries) 5.7 kg (12.5 lb)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
Swift UT portable unit. Incl. a premium-quality 26.4cm (10.4in) multi-touch display and high-capacity 100GB SSD. Software for B-Scan, integrated joystick, AC PS, 2x hot swap. Li-ion batt. w/ charger, manual & transport case. For Scorpion2 crawler.
TSC Amigo2 ACFM Array System - NEW (Amigo2)
Amigo2 inst. with a large multi-touch display. Supp. legacy, SENSU, SENSU2 probes and array. Includes 2 batt., AC PSU, test block and transp. case.
Highlights :
SPECS :
ACFM connectors 1x Sensu 2,1x Sensu,1x Legacy
ACFM frequency 5 KHz, 50 KHz
Acquisition modes Clock, Encoded
Array connectors 1x Sensu 2
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Critical Zone Inspection (Curved Scaning) Yes
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
High temperature inspections Yes
Highly portable easy to use system Yes
Multitouch control Yes
Paperless Reporting Yes
Rapid Coverage Yes
Remote control availability Yes
Rope access applications Yes
Automatic screenshot with defect entry Yes
Batteries - type 2x li-ion, rechargeable, DOT compliant
Communications Ethernet
Compliance ASME, EN 61010-1, CE, WEEE, FCC Part 15B, ICES-003, AS/NZS CISPR 22, RoHS
Data readback on PC software Yes
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors Fischer DBPU 1031 A012–130
Inspection workflows Yes
Optional PC software available Yes
Probe recognition and setup (ChipID) Yes
Support custom application and probes Yes
Harness available Yes
Connectivity Gigabit Ethernet, Wi-Fi, Dual Mode Bluetooth® 2.1, 2.1 EDR, 3.0, 3.0 HS, 4.0 (BLE), USB 2.0 (×3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 2 inputs, quadrature
IP rating IP65
Operating humidity 95%, non-condensing
Operating temperature -10° to 45°C (14 to 113°F)
Power supply/requirements 100–240 VAC ± 10% 50–60 Hz
Supported Technologies/Techniques ACFM
Storage temperature -20°C to 60°C (-4°F to 140°F)
Volume 13L (793.31 in3)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
APPLICATIONS :
Highlights :
- Detect and size surface cracks through paint and coatings
- Portable, battery-operated, sealed, large bright display
- Supports previous-generations/legacy probes
SPECS :
ACFM connectors 1x Sensu 2,1x Sensu,1x Legacy
ACFM frequency 5 KHz, 50 KHz
Acquisition modes Clock, Encoded
Array connectors 1x Sensu 2
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Critical Zone Inspection (Curved Scaning) Yes
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
High temperature inspections Yes
Highly portable easy to use system Yes
Multitouch control Yes
Paperless Reporting Yes
Rapid Coverage Yes
Remote control availability Yes
Rope access applications Yes
Automatic screenshot with defect entry Yes
Batteries - type 2x li-ion, rechargeable, DOT compliant
Communications Ethernet
Compliance ASME, EN 61010-1, CE, WEEE, FCC Part 15B, ICES-003, AS/NZS CISPR 22, RoHS
Data readback on PC software Yes
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors Fischer DBPU 1031 A012–130
Inspection workflows Yes
Optional PC software available Yes
Probe recognition and setup (ChipID) Yes
Support custom application and probes Yes
Harness available Yes
Connectivity Gigabit Ethernet, Wi-Fi, Dual Mode Bluetooth® 2.1, 2.1 EDR, 3.0, 3.0 HS, 4.0 (BLE), USB 2.0 (×3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 2 inputs, quadrature
IP rating IP65
Operating humidity 95%, non-condensing
Operating temperature -10° to 45°C (14 to 113°F)
Power supply/requirements 100–240 VAC ± 10% 50–60 Hz
Supported Technologies/Techniques ACFM
Storage temperature -20°C to 60°C (-4°F to 140°F)
Volume 13L (793.31 in3)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
APPLICATIONS :
- Weld inspection: with standard probes and single-pass array probes
- One or two-person operation (e.g. confined spaces)
- High-temperature applications
- Inspection through thick coatings
- Thread inspection
- Underwater inspection
Amigo2 inst. with a large multi-touch display. Supp. legacy, SENSU, SENSU2 probes and array. Includes 2 batt., AC PSU, test block and transp. case. Requires Assist GO software subscription, sold separately.
Reddy with 64-channel Eddy Current Array - NEW (Reddy 64-channel)
Reddy portable 64-ch. surface ECA instrument with a large, premium-quality multi-touch display. Incl. 2 batt., power supp., manual, rugged case.
Highlights :
Array connectors 1x 160 pin
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Highly portable easy to use system Yes
Multitouch control Yes
Nb. of array channels 64
Nb. of input channels 8
Probability of detection High
Rope access applications Yes
Setup creation/management Setup wizards
Acquisition rate Up to 50 000 samples/sec
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance ASME, EN 61010-1, CE, WEEE, FCC Part 15B, ICES-003, AS/NZS CISPR 22, RoHS
Data readback on PC software Yes
ECA frequency range 5 Hz - 10 MHz
ECA multiplexer SmartMUX
ECT connectors 1X 19-pin Fischer
ECT frequency range 5 Hz - 10 MHz
ECT simultaneous frequency Up to 160
Encoders and I/O connectors 12-pin Fischer
Frequency range 5 Hz–10 MHz
Inspection workflows Optimized, with hard buttons
Input impedance 50 or 100 Ohms
Injection modes Multiplexed, simultaneous, continuous
Optional PC software available Yes
Output voltage Up to 20 Vpp
Probe recognition and setup (ChipID) Automatic
Support custom application and probes Yes
Synchronization with I/O Yes
Harness available Yes
Connectivity Gigabit Ethernet, Wi-Fi, Dual Mode Bluetooth® 2.1, 2.1 EDR, 3.0, 3.0 HS, 4.0 (BLE), USB 2.0 (×3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 2 axes, quadrature
IP rating Designed for IP65
Operating humidity 95%, non-condensing
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements Direct VAC or onboard batteries
Supported Technologies/Techniques ECT, ECA
Volume 13L (793.31 in3)
Weight (without batteries) 5.7 kg (12.5 lb)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
APPLICATION :
Highlights :
- Very capable unit for surface ECA inspections
- No MFL capabilities
- Upgradable later to 128-channel, with or without MFL
Array connectors 1x 160 pin
Batteries - typical life 6-8 hours
Cooling Sealed and fanless
Data storage SSD, 100 GB
Display resolution 1024 × 768
Display size 26.4 cm (10.4")
Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement
Highly portable easy to use system Yes
Multitouch control Yes
Nb. of array channels 64
Nb. of input channels 8
Probability of detection High
Rope access applications Yes
Setup creation/management Setup wizards
Acquisition rate Up to 50 000 samples/sec
Batteries - type 2x li-ion, rechargeable, DOT compliant
Compliance ASME, EN 61010-1, CE, WEEE, FCC Part 15B, ICES-003, AS/NZS CISPR 22, RoHS
Data readback on PC software Yes
ECA frequency range 5 Hz - 10 MHz
ECA multiplexer SmartMUX
ECT connectors 1X 19-pin Fischer
ECT frequency range 5 Hz - 10 MHz
ECT simultaneous frequency Up to 160
Encoders and I/O connectors 12-pin Fischer
Frequency range 5 Hz–10 MHz
Inspection workflows Optimized, with hard buttons
Input impedance 50 or 100 Ohms
Injection modes Multiplexed, simultaneous, continuous
Optional PC software available Yes
Output voltage Up to 20 Vpp
Probe recognition and setup (ChipID) Automatic
Support custom application and probes Yes
Synchronization with I/O Yes
Harness available Yes
Connectivity Gigabit Ethernet, Wi-Fi, Dual Mode Bluetooth® 2.1, 2.1 EDR, 3.0, 3.0 HS, 4.0 (BLE), USB 2.0 (×3)
Dimensions (W x D x H) 355×288×127 mm (14.0×11.3×5.0 in)
Encoder inputs 2 axes, quadrature
IP rating Designed for IP65
Operating humidity 95%, non-condensing
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements Direct VAC or onboard batteries
Supported Technologies/Techniques ECT, ECA
Volume 13L (793.31 in3)
Weight (without batteries) 5.7 kg (12.5 lb)
Video output HDMI
Weight (with batteries) 6.6 kg (14.5 lb)
APPLICATION :
Depending on the instrument configuration:
- Corrosion on ferromagnetic pipes, tank walls and more
- Detecting and sizing cracks in stainless steel welds
- Detecting and assessing stress corrosion cracking
- Butt weld and fillet weld inspection for cracking and surface discontinuities
- Faster, less operator-dependant, surface inspection compared to PT/MT
- Assessing corrosion on aluminum and stainless steel tank floors
- Gear inspection
- Pipeline integrity
Reddy portable 64-ch. surface ECA instrument with a large, premium-quality multi-touch display. Very capable unit for surface ECA inspections . No MFL capabilities . Upgradable later to 128-channel, with or without MFL.
M2M Mantis 16:64PR with PAUT, UT, TOFD - NEW (M2M Mantis)
M2M MantisTM is a robust and lightweight flaw detector offering UT, PAUT, TOFD, and TFM through the streamlined user interface called CaptureTM. Based on a 16:64PR architecture with three different models, Mantis addresses both general and advanced applications without compromising productivity.
M2M MantisTM is a robust and lightweight flaw detector offering UT, PAUT, TOFD, and TFM through the streamlined user interface called CaptureTM. Based on a 16:64PR architecture with three different models, Mantis addresses both general and advanced applications without compromising productivity.
Made for the Field
– Portable, reinforced robust casing designed for IP65
– Compact and light for easy operation
– Resistive touch screen technology (glove compatible, not dust/water sensitive)
– High storage capacity – 128GB SSD
– IPEX PA, LEMO-00 UT and LEMO-16 encoder connectors
– Embedded Easy Latch adaptor available
– One internal battery one hot-swappable battery
– Connectivity with WI-FI, USB 3 and Gbit Ethernet
Designed for Your Inspection
– 16:64PR architecture plus two UT channels verified with international standards
– Compatible with existing phased array probes (linear, dual linear, and dual matrix array) and existing scanners (up to three encoder axis)
– Embedded focal law calculation (sectorial, linear, compound) on all parts through Capture software
– Up to eight group configurations
– High inspection speeds thanks to PRF up to 20 kHz
– Real-time FMC/TFM with up to 64 elements for code compliant inspections
Ecosystem, powered by CAPTURE
CAPTURE-GO embedded, with advanced analysis tools (auto-sizing, 3D data display, stitching)
Ideal for quick set-up, inspection, analysis, and reporting, covering your complete inspection task
RMS Control ready (motorized scanner)
CAPTURE PC versions available for set-up design and analysis
File compatibility with GEKKO
Connectivity for remote support or remote inspection (Wi-Fi™, USB 3.0 and Gigabit Ethernet)
SPECS :
A-Scan height (dynamic range) Up to 800%
Adaptive TFM (ATFM) No
Array connectors 1x IPEX
Batteries - typical life Up to 4 hours
Cooling Sealed with external fans
Data storage SSD, 128 GB
Display resolution 1024 × 768
Display size 21 cm (8.4")
Display type High contrast resistive touch screen
Maximum active aperture 16
Nb. of receiving elements 64
Paperless Reporting Yes
Pulser (PAUT) voltage From 12 V to 90 V (with 1 V steps)
Pulser (UT) voltage From 12 V to 200 V (with 1 V steps)
Remote control availability Yes
Rope access applications Yes
Setup creation/management Setup wizards, application
Shockproof rating According to MIL-STD-810G
Total Focusing Method (TFM) No
Batteries - type 1x li-ion, rechargeable, DOT compliant
Compliance EN ISO 18563-1:2015 GR2, EN 12668-1:2010 GR2, AITM-00016 Issue5 table7; AITM-00013 Issue 6 Table11
Data readback on PC software Yes
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors 1x 16-pin LEMO
Frequency range 0.4 MHz to 20 MHz
Gain range (PAUT) Up to 120 dB (0.1 dB steps)
Gain range (UT-TOFD) Up to 120 dB (0.1 dB steps)
Gates Floating and tracking for repeatable and reliable results
Input impedance 50 Ohms
Optional PC software available Yes
Programmable alarms Yes
Pulse type (PAUT) Negative square pulse
Pulse type (UT-TOFD) Negative square pulse
Pulse width 10 ns to 1000 ns
Support custom application and probes Yes
UT connectors 2x LEMO 00
UT/TOFD connectors 2x LEMO 00
Synchronization with I/O Yes
Full screen mode Yes
Connectivity Gigabit Ethernet, Wi-fi, USB 2.0 (x1), USB 3.0 (x1)
Dimensions (W x D x H) 311x220x86 mm
External trigger 0
Encoder inputs 3-axis, TTL (5V)
IP rating Designed for IP65
Operating humidity 12%RH – 78%RH
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements 15 V, 6 A
Programmable outputs No
Pulser (PAUT) fall time <10 ns
Pulser (UT-TOFD) fall time <10 ns
Reload data from defect table Yes
Supported Technologies/Techniques UT, TOFD, PAUT
Storage SSD, 128 GB
Storage temperature -20°C to 60°C (-4°F to 140°F)
Volume 5.88 L (359 in3)
Weight (without batteries) 3.2 kg (7 lb)
Video output HDMI
Weight (with batteries) 3.7 kg (8.2 lb)
APPLICATIONS :
M2M MantisTM is a robust and lightweight flaw detector offering UT, PAUT, TOFD, and TFM through the streamlined user interface called CaptureTM. Based on a 16:64PR architecture with three different models, Mantis addresses both general and advanced applications without compromising productivity.
Made for the Field
– Portable, reinforced robust casing designed for IP65
– Compact and light for easy operation
– Resistive touch screen technology (glove compatible, not dust/water sensitive)
– High storage capacity – 128GB SSD
– IPEX PA, LEMO-00 UT and LEMO-16 encoder connectors
– Embedded Easy Latch adaptor available
– One internal battery one hot-swappable battery
– Connectivity with WI-FI, USB 3 and Gbit Ethernet
Designed for Your Inspection
– 16:64PR architecture plus two UT channels verified with international standards
– Compatible with existing phased array probes (linear, dual linear, and dual matrix array) and existing scanners (up to three encoder axis)
– Embedded focal law calculation (sectorial, linear, compound) on all parts through Capture software
– Up to eight group configurations
– High inspection speeds thanks to PRF up to 20 kHz
– Real-time FMC/TFM with up to 64 elements for code compliant inspections
Ecosystem, powered by CAPTURE
CAPTURE-GO embedded, with advanced analysis tools (auto-sizing, 3D data display, stitching)
Ideal for quick set-up, inspection, analysis, and reporting, covering your complete inspection task
RMS Control ready (motorized scanner)
CAPTURE PC versions available for set-up design and analysis
File compatibility with GEKKO
Connectivity for remote support or remote inspection (Wi-Fi™, USB 3.0 and Gigabit Ethernet)
SPECS :
A-Scan height (dynamic range) Up to 800%
Adaptive TFM (ATFM) No
Array connectors 1x IPEX
Batteries - typical life Up to 4 hours
Cooling Sealed with external fans
Data storage SSD, 128 GB
Display resolution 1024 × 768
Display size 21 cm (8.4")
Display type High contrast resistive touch screen
Maximum active aperture 16
Nb. of receiving elements 64
Paperless Reporting Yes
Pulser (PAUT) voltage From 12 V to 90 V (with 1 V steps)
Pulser (UT) voltage From 12 V to 200 V (with 1 V steps)
Remote control availability Yes
Rope access applications Yes
Setup creation/management Setup wizards, application
Shockproof rating According to MIL-STD-810G
Total Focusing Method (TFM) No
Batteries - type 1x li-ion, rechargeable, DOT compliant
Compliance EN ISO 18563-1:2015 GR2, EN 12668-1:2010 GR2, AITM-00016 Issue5 table7; AITM-00013 Issue 6 Table11
Data readback on PC software Yes
Defect table (for reporting) Yes
Digitizing 16-bit resolution
Encoders and I/O connectors 1x 16-pin LEMO
Frequency range 0.4 MHz to 20 MHz
Gain range (PAUT) Up to 120 dB (0.1 dB steps)
Gain range (UT-TOFD) Up to 120 dB (0.1 dB steps)
Gates Floating and tracking for repeatable and reliable results
Input impedance 50 Ohms
Optional PC software available Yes
Programmable alarms Yes
Pulse type (PAUT) Negative square pulse
Pulse type (UT-TOFD) Negative square pulse
Pulse width 10 ns to 1000 ns
Support custom application and probes Yes
UT connectors 2x LEMO 00
UT/TOFD connectors 2x LEMO 00
Synchronization with I/O Yes
Full screen mode Yes
Connectivity Gigabit Ethernet, Wi-fi, USB 2.0 (x1), USB 3.0 (x1)
Dimensions (W x D x H) 311x220x86 mm
External trigger 0
Encoder inputs 3-axis, TTL (5V)
IP rating Designed for IP65
Operating humidity 12%RH – 78%RH
Operating temperature 0°C to 40°C (32°F to 104°F)
Power supply/requirements 15 V, 6 A
Programmable outputs No
Pulser (PAUT) fall time <10 ns
Pulser (UT-TOFD) fall time <10 ns
Reload data from defect table Yes
Supported Technologies/Techniques UT, TOFD, PAUT
Storage SSD, 128 GB
Storage temperature -20°C to 60°C (-4°F to 140°F)
Volume 5.88 L (359 in3)
Weight (without batteries) 3.2 kg (7 lb)
Video output HDMI
Weight (with batteries) 3.7 kg (8.2 lb)
APPLICATIONS :
Depending on the instrument configuration:
- Weld inspection (UT, TOFD, PAUT, TFM, PWI)
- Corrosion mapping, including large areas
- Multi-group weld inspection procedures fully covered
- Flange face
- Bolt inspection
- Composite inspection
M2M MantisTM is a robust and lightweight flaw detector offering UT, PAUT, TOFD, and TFM through the streamlined user interface called CaptureTM. Based on a 16:64PR architecture with three different models, Mantis addresses both general and advanced applications without compromising productivity.
- 1