Ether NDE
The ViCTor 2.2D is a user friendly automated eddy current inspection system designed with the Automation Engineer in mind. Based on the AeroCheck , NDT Inspectors will become quickly familiar with its user interface and with a variety of case configurations available. The ViCTor 2.2D offers maximum flexibility for each individual application.
The PhaseCheck share the same features and performance of the AeroCheck Eddy Current Flaw Detector combined with the ability to scan areas and document inspection results using a C-Scan Display and X/Y and R/Theta manual scanners with easy scan calibration. The ETher NDE PhaseCheck can be used with all reflection, bridge and absolute probes from all manufacturers and uses industry standard 12-Way Lemo and Co-axial Lemo 00 connectors, reducing the need to use adapters.
The ETi-200 Eddy Current Flaw Detector is designed to offer advanced multi-frequency and multi-channel flaw detection while offering unmatched flexibility and portability on the market. Appealing to all sectors within NDT, the ETi-200 allows the operator to program not only frequency, but many other advanced functions. In dual-probe mode, the ETi-200 will multiplex four channels per probe whereas in single probe mode up to eight channels are available. A cast aluminum enclosure and protective rubber over-molding make the ETi-200 extremely durable and robust.
The ETi-300 is an advanced eddy current tube testing instrument for inspecting non-ferrous tubing from the inner diameter (ID), developed by ETher NDE to perform in the most demanding of environments whilst delivering outstanding inspection results and reporting functionality. Eddy Current testing has long been acknowledged as the fastest, most efficient and effective inspection method to inspect the large quantity of non-ferrous tubes present in a typical heat exchanger. The ETi-300 instrument and it’s suite of analysis and reporting software is ideal for heat exchanger and condenser inspection applications within Power Generation, Transportation, Petrochemical and Oil and Gas industries.
The SteelCheck is an affordable, battery operated, portable 3 channel(Hall Sensor and 2 coil) tube inspection unit for Carbon Steel (Ferromagnetic Tubes) using Magnetic Flux Leakage. Unlike other remote field eddy current method it is unaffected by external Aluminum Fins and has the capability to discriminate between external and internal defects.
As an advanced flaw detector for weld inspection the WeldCheck Plus delivers dual channel/frequency capability, Automatic Lift Off Gain Compensation (LOGC) and conductivity measurement, further enhancing the operator's inspection capability in the field. LOGC automatically compensates for coating thickness variations in real time further improving the quality of the inspection results.
The WeldCheck Series of Flaw Detectors appeals to users across a wide range of sectors including Offshore, Rope Access, Infrastructure NDT applications, plus other weld inspection requirements replacing MPI and LPI, especially on coated welds.The WeldCheck2 EC Flaw Detector is single channel, 10Hz- 20MHz, lightweight eddy current flaw detector, housed in a tough aluminium alloy Mg Si 0.5 powder-coated outer case with rubber end bumpers and has been designed with the end user in mind and was developed to meet the requirements on EN1711 & ISO 17643 "Eddy Current Examination of Welds by Complex Phase Analysis"
EtherCheck offers the operator a rich range of features combined with the most widely used acoustic bond testing method; Pitch-Catch. A common user interface between the two modes, resulting in simple operator led set up.The EtherCheck is a combined Eddy Current and Bond Testing Flaw Detector. It comes with a rich range of features offered by a best in class eddy current flaw detector combined with the most widely used acoustic bond testing method; Pitch-Catch. Features a single frequency range of 10Hz-20MHz and dual range of 10Hz-12.8MHz.
The AeroCheck offers the end user dual frequency capability, with an excellent Frequency Range from 10Hz to 12.8MHz, with Rotary Drive Capabilities as standard, but in addition offers Auto-mix and Conductivity Measurement.The AeroCheck Series can be used with all reflection, bridge and absolute probes from all manufacturers and uses industry standard 12-Way Lemo and Co-axial Lemo 00 connectors, reducing the need to use adapters.
The AeroCheck 2 is the single frequency EC flaw detector, 10Hz-20MHz, offering all the advanced features, including Loop, Guides and Trace, plus Rotary, but without Conductivity capability.
ETher NDE Victor 2.2D Eddy Current Flaw Detector - NEW (Victor 2.2D)
Lightweight, User Friendly & Automated
The ViCTor 2.2D is a user friendly automated eddy current inspection system designed with the Automation Engineer in mind. Based on the AeroCheck , NDT Inspectors will become quickly familiar with its user interface and with a variety of case configurations available. The ViCTor 2.2D offers maximum flexibility for each individual application.
Ideally suited to inspection automation for the following reasons:
Non-Contact
High Speed (potentially up to 200ms)
No coupling needed, no effluent produced
Ideal for surface defect detection
Wide Geometry of probes available
Cost effective inspection solution for Bearings, Gudgeon Pins, Cylinder Liners
Features
Capable of simultaneous use of two probes, for increased inspection efficiency
Separate dual alarms
Rotary Drive and Conductivity operating modes on-board
Configurable I/O capability using voltage free contacts.
Large, bright LCD screen and external VGA for monitor output
Powered by 24V for easy industrial control system integration
RS-232 & USB remote control for easy control system integration
Ability to stream real time data over a USB
Dual analogue outputs enable simple recording
A DLL is available to permit software integration by the end user.
Applications
Surface breaking defects
Sub-surface defects in non-ferrous materials
Heat treatment / material property verification
Sensing applications for verifying geometry such as the presence of threads, butt weld detection.
Special Features
Guides Feature: Allows the user to display a slide show that can be created easily with commonly used desktop software. Instructions, tutorials and procedures can be added quickly and the NDT inspector can easily switch between the inspection itself and the Guides while performing a live test.
Innovative Loop Feature: Captures a live repetitive signal and then adjusts the instrument settings especially Phase, Gain and Filters in order to simplify the task of optimizing the parameters.
Data Logging: Real time recording or signal data and replay on instruments & desktop PC, up to 164 seconds
Trace Function: Allows a reference waveform to be stored on the screen and appears along the graticule behind the live spot, allowing the operator to readily compare the live data with the reference calibration.
Victor 2.2D Specification
Standard Kit Includes
Victor 2.2D Two Channel Eddy Current Flaw Detector
Software Manual on USB Stick with Rotary & Conductivity
Mains Power Supply, Input Voltage 90-264 VAC
Mains Lead - 2m
I/O Connector - 15-Way Male sub-D Connector, Metal Straight Hood
Optional Accessories
A wide range of probes are available
Weld Probe Kits
Surface Probe Kit
Sub Surface Probe Kit
Rotary Probe Kit
Conductivity Probe Kit
Tube Probe Kit
The ViCTor 2.2D is a user friendly automated eddy current inspection system designed with the Automation Engineer in mind. Based on the AeroCheck , NDT Inspectors will become quickly familiar with its user interface and with a variety of case configurations available. The ViCTor 2.2D offers maximum flexibility for each individual application.
Ideally suited to inspection automation for the following reasons:
Non-Contact
High Speed (potentially up to 200ms)
No coupling needed, no effluent produced
Ideal for surface defect detection
Wide Geometry of probes available
Cost effective inspection solution for Bearings, Gudgeon Pins, Cylinder Liners
Features
Capable of simultaneous use of two probes, for increased inspection efficiency
Separate dual alarms
Rotary Drive and Conductivity operating modes on-board
Configurable I/O capability using voltage free contacts.
Large, bright LCD screen and external VGA for monitor output
Powered by 24V for easy industrial control system integration
RS-232 & USB remote control for easy control system integration
Ability to stream real time data over a USB
Dual analogue outputs enable simple recording
A DLL is available to permit software integration by the end user.
Applications
Surface breaking defects
Sub-surface defects in non-ferrous materials
Heat treatment / material property verification
Sensing applications for verifying geometry such as the presence of threads, butt weld detection.
Special Features
Guides Feature: Allows the user to display a slide show that can be created easily with commonly used desktop software. Instructions, tutorials and procedures can be added quickly and the NDT inspector can easily switch between the inspection itself and the Guides while performing a live test.
Innovative Loop Feature: Captures a live repetitive signal and then adjusts the instrument settings especially Phase, Gain and Filters in order to simplify the task of optimizing the parameters.
Data Logging: Real time recording or signal data and replay on instruments & desktop PC, up to 164 seconds
Trace Function: Allows a reference waveform to be stored on the screen and appears along the graticule behind the live spot, allowing the operator to readily compare the live data with the reference calibration.
Victor 2.2D Specification
| Probe | Connectors | 2 off 12 Way Lemo 2B (Absolute, Bridge and Reflection) and Lemo 00 (for single element absolute probes) |
| Rotary | Probe 1 only. 600-3000 rpm - ETher Mercury Drive (ARD002), Hocking 33A100 / 40A100, Rohmann MR3 and SR2 Drive (special adapter needed). | |
| Connectivity | Probe 1 only. Option becomes active with use of AeroCheck conductivity probe and cable | |
| Frequency | Dual Frequency | 10 Hz to 12.8 MHz |
| Gain | Overall | -18 to 104 dB |
| Main Gain | -18 to 82dB, 0.1, 1 and 6dB steps | |
| Input | 0dB or 12dB | |
| Drive | 0dB, 6dB and 10dB (0dB reference 1mW into 50 ohm) | |
| Max X/Y Ratio | -18dB to 82dB independent | |
| Phase | Range | 0.0 - 359.9°, 0.1° steps |
| Filters | Normal High Pass | DC to 2kHz or Low Pass Filter, which ever is the lower in 1 Hz steps. Plus variable adaptive balance drift compensation 0.01 - 0.5 Hz (6 steps). |
| Normal Low Pass | 1Hz to 2kHz or a quarter of the lowest test frequency whichever is lower in 1Hz steps. | |
| Balance | Manual | 14 internal balance loads; 2.2µh, 5.0µh, 6.0µh, 6.5µh, 7.0µh, 7.5µh, 8.2µh, 12µh, 15µh, 18µh, 22µh, 30µh, 47µh, 82µh |
| Automatic | Optimized balance load selection | |
| Mix Channel | Frequency | Full frequency range available on both channels |
| Probe Mode | Simultaneous reflection / bridge and absolute including simultaneous two probe Differential and Absolute | |
| Mix Gain | X/Y -18 to 18dB | |
| Mix Phase | 0.0 - 359.9°, 0.1° steps | |
| Alarm Gates | Number | 2 independent Alarm Gates may be configured on Pane 1, Pane 2 or Both Panes (logical or) |
| Box | Fully configurable, Freeze, Tone or Visual | |
| Sector | Fully configurable, Freeze, Tone or Visual | |
| Display | Type | 5.7" (145mm), 18 bit color, daylight readable |
| Viewable Area | 4.5" (115.2mm) Horizontal x 3.4" (86.4mm) Vertical | |
| Resolution | 640 x 480 pixels | |
| Color Schemes | User configurable Dark, Bright and Black & White | |
| Configurable Screen | Full Screen, Single, Dual Spot or Dual Pane with variable size and location and functions. e.g. XY, Time base, Waterfall and Meter. | |
| Display Modes | Spot, Time base (0.1-20 seconds x 1-200 sweeps and up to 55 seconds), Waterfall and Meter with peak hold and % readout. | |
| Graticules | None, Grid (4 sizes: 5, 10, 15 and 20% FSH), Polar (4 sizes: 5, 10, 15 and 20% FSH) | |
| Offset | Spot Position: Y=-50 to 50, X=-65 to 65% | |
| Spot Readout | Display X, Y, or R, θ | |
| Summary | Display of all settings in Legacy Format | |
| Removable Data Storage | Setup Storage | micro SD up to 32GB, holding over 10,000 settings |
| Stored Screen Shots | micro SD up to 32GB, holding over 10,000 screen shots | |
| Recorded Data | micro SD up to 32GB, holding over 500 2.5 minute long data recordings | |
| Guides | micro SD up to 32GB, holding 10,000 slides | |
| Advanced Features | Data Logging | Real-time recording of signal data and replay on instruments and desktop PC up to 164 seconds |
| Guides | Create and display a slide show containing instructions, tutorials and procedures using Microsoft PowerPoint | |
| Attachments | Screenshots and Data Recordings are saved in a folder with the name of the Settings | |
| Loop | Capture a live repetitive signal and then optimize the instrument settings (Phase, Gain, Filters) to simplify optimizing the parameters. | |
| Trace | Allows a calibration reference signal to be stored on the screen and then compared with the live signal | |
| Auto Phase | Allows phase angle to be automatically set to a pre set angle | |
| Inputs/Outputs | PC Connectivity | USB (Full PC remote control plus Real Time data) and RS232 May be set off, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 baud |
| Analogue | 2 outputs 2 Volts swing | |
| Digital Volt Free Alarm | on Lemo 12 way Open collector transistor (36 V DC at 10mA Max.) | |
| VGA | Full 15 way VGA output (EC screens only) | |
| l/O | Two configurable | |
| Alarm Out | 2 off Opto isolated 2mA 50V Max. | |
| External Alarm Inhibit | 2 TTL inputs | |
| Languages | English, French, Spanish, Italian, Portuguese, Russian, Japanese, Chinese, Turkish, Czech | |
| Verification | The system includes on delivery a 2 yr. validity Verification Level 2 detailed functional check and calibration as per ISO 15548-1:2013 | |
| Power on Self Test | The system performs a self test on start up of external RAM, SD, RAM, accelerometer, Micro SD card, LCD screen buffer | |
| Power | External | 100-240VAC, 50-60Hz, 30 Watts |
| Physical | Weight | 7.25 lbs. (3.3 kg) |
| Size (WxHxD) | 9.7" x 6.0" x 9.9" (246 x 152 x 250 mm) | |
| Operating Temperature | -4° to 140° (-20° to 60°C) | |
| Storage Temperature | Storage for up to 12 months -4° to 95°F (-20° to 35°C) Nominal 68°F (20°C) | |
| IP Rating | IP54 (front panel only) |
Standard Kit Includes
Victor 2.2D Two Channel Eddy Current Flaw Detector
Software Manual on USB Stick with Rotary & Conductivity
Mains Power Supply, Input Voltage 90-264 VAC
Mains Lead - 2m
I/O Connector - 15-Way Male sub-D Connector, Metal Straight Hood
Optional Accessories
A wide range of probes are available
Weld Probe Kits
KAWEL001 Weld Probe Accessories Kit Includes
- PWM100S00 Probe, Weld, Dia 16.00mm (Medium) 100kHz, Straight, Disconnect
- PUB100K Probe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC
- ATBW Accessory. Test Block, Weld Probe, Ferrous (Steel EN1A) x4 0.5mm Shims, 0.5, 1.0, 2.0mm slots
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
KAWEL002 Advanced Weld Probe Accessories Kit Includes
- PWS100S000 Probe, Weld, Dia 11.00mm (Small) 100kHz, Straight, Disconnect
- PWM100S00 Probe, Weld, Dia 16.00mm (Medium) 100kHz, Straight, Disconnect
- PUB100K Probe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC
- ATB016 Accessory, Test Block WeldCheck Demo Crack Specimen -
- Plate with two cracks, Type A and C - Toe and Cap
- Plates are 5" x 5", 1/4" thick with false ground crown.
- Standard crack size 1/4" Long x 0.040" deep.
- ATBW Accessory. Test Block, Weld Probe, Ferrous (Steel EN1A) x4 0.5mm Shims, 0.5, 1.0, 2.0mm slots
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
Surface Probe Kit
KASUR001 Surface Inspection Kit Includes
- PU500PSFE/NFE Probe, Unshielded, 500kHz, Fe/NFe, Plastic Handle, Straight, 100mm Long
- PS002PS028-114N Probe, Shielded, 2MHz, Plastic Handle, Straight, 28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)
- PS500PD064-114N Probe, Shielded, 500kHz, Plastic Handle, Double Crank, 6.4 (0.25") Tip Length (Total Length 114mm, 4.5") (15deg Crank, 90deg tip Shank)
- PS002PD064-114N Probe, Shielded, 2MHz, Plastic Handle, Double Crank, 6.4 (0.25") Tip Length (Total Length 114mm, 4.5") (15deg Crank, 90deg tip Shank)
- PK065002NFE Probe, Knife, 65 deg, 2MHz, NFe, Unshielded
- ALLCX-M02-015A Accessory, Lead, Lemo 00 to Microdot, 1.5m (Vantage/ETi)
- ATBF Accessory. Test Block, Ferrous (Steel EN1A), 0.2, 0.5, 1.0mm slots
- ATBA Accessory. Test Block, Aluminum Alloy 7075-T6, 0.2, 0.5, 1.0mm slots
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
Sub Surface Probe Kit
KASUBS001 Sub Surface, Low Frequency Inspection Kit includes
- PUS16 Probe, Surface, Straight, Dia 16mm, 300Hz - 100KHz, Plastic, Lemo 4-Way
- PUR11 Probe, Surface, Right Angled, Dia 11mm, 300Hz - 100KHz, Plastic, Lemo 4-Way
- ALL12-L04-015R Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ATB001 Accessory, Test Block, Aluminum 7075-T6, 1.6mm Thick, x4 Flat Bottom Holes 75%(1.2mm), 50%(0.8mm), 25%(0.4mm), 12.5%(0.2mm), Deep.
Rotary Probe Kit
KAROT001 Rotary Drive Inspection Kit Includes
- ARD002 Accessory, Rotating Drive, Small, Lemo 12-Way., (MERCURY)
- ALL12-L12-020M Accessory, Lead, Lemo 12-Way - Lemo 12-Way, , 2.0m (Rotating Drive)
- AC002 Accessory, Deluxe Probe Case PHDC1
Conductivity Probe Kit
KACON001 Conductivity, Standard 13mm Probe Inspection Kit Includes (NIST ONLY)
- PCON001 Probe, Conductivity, 60kHz, Dia 13.00mm, Straight Lemo 7-Way (AeroCheck Plus) c/w Qiuick Reference Card (APCON001)
- ALL12-L07-012-CON Accessory, Lead, 12-Way Lemo to 7-Way Lemo, 1.2m, Conductivity (To fit AeroCheck Plus Conductivity Probe)
- ASIG014 Accessory, Dual Conductivity Reference Standards, Nominal Value 9.4% IACS (Nickel Silver) & Nominal Value 58.8% IACS
(Aluminum Alloy), (Recommended for Aluminum Alloy use) (SigmaCheck/SigmaCheck2) NIST VALUES - 40516 SKIRT - Conductivity Probe (AeroCheck Plus)
- 40517 REFERENCE HOLDER - Dual Condustivity Standard (Thermal Bridge for Stability)
- B3061S x 10LG PLASTIC SCREW (EGT5 M3x0.5 x 10mm Long, Natural)
- APCON001 Quick Reference Card - Guide to using Conductivity Probe PCON001
- AC002 Accessory, Deluxe Probe Case PHDC1
Tube Probe Kit
KATUB001 Tube Inspection Kit Includes
- PID138D0018K Probe, Internal Diameter, Differential, Dia 13.80, Dis-connect, 18k.
- CIDL03F Accessory, ID Lead,12-Way Lemo, Flexible, 3.0m
- ATBTB1587 Accessory, Test Block, Tube, Brass, OD 5/8" , (15.87mm) x 20swg, Calibration Tube
- ATB010 Accessory, Test Block, ID Probe Support Ring OD 25.4 x ID 16.6 x 20.00mm Long
The ViCTor 2.2D is a user friendly automated eddy current inspection system designed with the Automation Engineer in mind. Based on the AeroCheck , NDT Inspectors will become quickly familiar with its user interface and with a variety of case configurations available. The ViCTor 2.2D offers maximum flexibility for each individual application.
ETher NDE PhaseCheck Eddy Current Flaw Detector With C-Scan - NEW (PhaseCheck)
Introducing the latest addition to our core range, the PhaseCheck, an advanced dual probe, dual frequency advanced eddy current flaw detector with C-Scan capability.
For the first time in the field of portable NDT instruments the PhaseCheck delivers the operator with a hand-held high-end eddy current flaw detector package, delivering C-Scan data display. As the saying goes “a picture is worth a 1000 words” and to date “pictures” , such as the inspection data displayed in C-Scan images, have been limited to expensive large laboratory instruments.
C-Scan Capabilities in a Handheld Design
They say “a picture is worth 1000 words”. To date, “pictures” (C-Scan) in Eddy Current have been limited to expensive large laboratory instruments. Now for the first time in a hand held high-end eddy current flaw detector package we add a C-Scan data display capability.
The PhaseCheck share the same features and performance of the AeroCheck Eddy Current Flaw Detector combined with the ability to scan areas and document inspection results using a C-Scan Display and X/Y and R/Theta manual scanners with easy scan calibration. The ETher NDE PhaseCheck can be used with all reflection, bridge and absolute probes from all manufacturers and uses industry standard 12-Way Lemo and Co-axial Lemo 00 connectors, reducing the need to use adapters.
Features
Dual Frequency with C-Scan capability
Data Logging - real time recording or signal data and replay on instruments and desktop PC, up to 164 seconds.
Supports X/Y and R/Theta manual scanners with easy scan calibration.
Allows up to 2 encoders to be connected, flexibility that will permit many scanner mechanisms to be interfaced.
Flexible Dual Bridge and Reflection Probe inspection
Ability to post analyze data for peer review and audit purposes
Readily incorporates C-scan inspection results in a report
User friendly interface, single level meu system, "quick function" sidebar
3-Year Standard Warranty (6-Year Extended Warranty with ETherCover)
C-Scan Capability
With up to 1 million data points, up to 1,000 stored data files and scaling from 0.1 to 999.9 Ticks/mm, the PhaseCheck delivers professional quality C-Scan capability in a handheld design. C-Scans can then also be exported as a Bitmap, Excel Spreadsheet or raw data file for subsequent analysis.
Works the Way You Do
The PhaseCheck features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Lightweight, Rugged and Easy to Use
Lightweight at 2.6 lbs. (1.2 kg) and housed in a rugged metal casing, the PhaseCheck offers up to eight hours battery life. The large "soft keys" and easy-to-navigate menu systems provide a very user-friendly interface.
ETherScan Viewer
The data recorded in the C-Scan can be further analyzed on-board the instrument by changing the channel views, the phase and gain, or exported for further analysis using the post analysis PC Application ETherScanViewer.
Top-Quality Warranties for Top-Quality Instruments
ETher NDE is unique in that they offer warranty coverage unlike anyone else in the field. All ETher Phase Plane Instruments come with the standard 3-year warranty, which covers all components of the instrument and only excludes customer damage or misuse. However, you can also opt in for an extended 6-year ETherCover warranty plan, putting it truly in a league of its own.
The ETherCover 6-Year Extended Warranty Includes:
Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
One Free of Charge Battery Swap within the six year period (if required)
One Free of Charge Keypad Replacement within the six-year period (if required)
Guaranteed Fast Repair
Free of Charge Software Upgrades within the six year period
ETher NDE PhaseCheck Specifications
Standard PhaseCheck Kit Includes
Optional Accessories
For the first time in the field of portable NDT instruments the PhaseCheck delivers the operator with a hand-held high-end eddy current flaw detector package, delivering C-Scan data display. As the saying goes “a picture is worth a 1000 words” and to date “pictures” , such as the inspection data displayed in C-Scan images, have been limited to expensive large laboratory instruments.
C-Scan Capabilities in a Handheld Design
They say “a picture is worth 1000 words”. To date, “pictures” (C-Scan) in Eddy Current have been limited to expensive large laboratory instruments. Now for the first time in a hand held high-end eddy current flaw detector package we add a C-Scan data display capability.
The PhaseCheck share the same features and performance of the AeroCheck Eddy Current Flaw Detector combined with the ability to scan areas and document inspection results using a C-Scan Display and X/Y and R/Theta manual scanners with easy scan calibration. The ETher NDE PhaseCheck can be used with all reflection, bridge and absolute probes from all manufacturers and uses industry standard 12-Way Lemo and Co-axial Lemo 00 connectors, reducing the need to use adapters.
Features
Dual Frequency with C-Scan capability
Data Logging - real time recording or signal data and replay on instruments and desktop PC, up to 164 seconds.
Supports X/Y and R/Theta manual scanners with easy scan calibration.
Allows up to 2 encoders to be connected, flexibility that will permit many scanner mechanisms to be interfaced.
Flexible Dual Bridge and Reflection Probe inspection
Ability to post analyze data for peer review and audit purposes
Readily incorporates C-scan inspection results in a report
User friendly interface, single level meu system, "quick function" sidebar
3-Year Standard Warranty (6-Year Extended Warranty with ETherCover)
C-Scan Capability
With up to 1 million data points, up to 1,000 stored data files and scaling from 0.1 to 999.9 Ticks/mm, the PhaseCheck delivers professional quality C-Scan capability in a handheld design. C-Scans can then also be exported as a Bitmap, Excel Spreadsheet or raw data file for subsequent analysis.
Works the Way You Do
The PhaseCheck features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Lightweight, Rugged and Easy to Use
Lightweight at 2.6 lbs. (1.2 kg) and housed in a rugged metal casing, the PhaseCheck offers up to eight hours battery life. The large "soft keys" and easy-to-navigate menu systems provide a very user-friendly interface.
ETherScan Viewer
The data recorded in the C-Scan can be further analyzed on-board the instrument by changing the channel views, the phase and gain, or exported for further analysis using the post analysis PC Application ETherScanViewer.
Top-Quality Warranties for Top-Quality Instruments
ETher NDE is unique in that they offer warranty coverage unlike anyone else in the field. All ETher Phase Plane Instruments come with the standard 3-year warranty, which covers all components of the instrument and only excludes customer damage or misuse. However, you can also opt in for an extended 6-year ETherCover warranty plan, putting it truly in a league of its own.
The ETherCover 6-Year Extended Warranty Includes:
Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
One Free of Charge Battery Swap within the six year period (if required)
One Free of Charge Keypad Replacement within the six-year period (if required)
Guaranteed Fast Repair
Free of Charge Software Upgrades within the six year period
ETher NDE PhaseCheck Specifications
| Operating Modes | Eddy Current Modes | C-Scan |
| Eddy Current Single Probe Frequency | ||
| Eddy Current Dual Probe Frequency | ||
| Eddy Current 2 Probe, 2 Channel | ||
| Rotating Drive | ||
| Conductivity with thickness | ||
| Probe | Connectors | Simultaneous probe operation possible using LEMO 12 way and LEMO 4 way |
| 12-Way LEMO 2B (Absolute, Bridge, Reflection, Rotary, Conductivity) | ||
| 4-Way LEMO 0B (Bridge, Reflection) | ||
| Rotary | 600-3000 rpm. ETher Mercury Drive (ADR002) and Saturn (ARD001), Hocking 33A100, Rohmann MR3, SR1 and SR2 Drive (special adapter needed) | |
| Conductivity | Option becomes active with use of AMCheck conductivity probe and cable. | |
| Frequency | Dual Frequency | Frequency Dual Frequency 10Hz - 12.8MHz & Mix -18 to 18dB on output |
| Gain | Overall | -18 to 104dB, 0.1, 1 and 6dB steps (104dB maximum) |
| Input | 0dB or 12dB | |
| Drive | 0dB, 6dB and 10dB (0dB reference 1mW into 50 ohm). | |
| Max X/Y Ratio | /-100.0 dB | |
| Phase | Range | 0.0-359.9°, 0.1° steps |
| Filters | High Pass | DC to 2kHz or Low Pass Filter, which ever is lower in 1Hz steps. Plus variable adaptive balance drift compensation 0.01 - 0.5 Hz (6 steps). |
| Low Pass | 1Hz to 2kHz or a quarter of the lowest test frequency, which ever is lower in 1 Hz steps. | |
| Balance Load | Manual | 14 internal balance loads; 2.2μH, 5.0μH, 6.0μH, 6.5μH, 7.0μH, 7.5μH, 8.2μH, 12μH, 15μH, 18μH, 22μH, 30μH, 47μH, 82μH |
| Automatic | Optimized balance load selection. | |
| Mix Channel | Frequency | Full frequency range available on both channels |
| Probe Mode | Simultaneous reflection / bridge and absolute including simultaneous two probe Differential and Absolute | |
| Mix Gain | X/Y -18 to 18dB | |
| Mix Phase | 0.0-359.9°, 0.1° steps | |
| Alarm Gates | Box | Fully configurable, Freeze, Tone or Visual. |
| Sector | Fully configurable, Freeze, Tone or Visual. | |
| Display | Type | 5.7” (145mm), 18 bit Color, daylight readable. |
| Viewable Area | 115.2mm (Horizontal) x 86.4mm (Vertical) | |
| Resolution | 640 x 480 pixels | |
| Flip | Manual or automatic screen orientation change to enable left or right handed use. | |
| Configurable Screen | Full Screen, Single, Dual Spot or Dual Pane with variable size and location and function e.g. XY, Timebase, Waterfall and Meter. | |
| Color Schemes | User configurable Dark, Bright and Black & White | |
| Display Modes | Spot, Time base (0.1-20 seconds x 1-200 sweeps, up to 55 seconds), Waterfall, Meter with peak hold and % readout, Distance (single axis, changes with direction), Strip Chart (single axis, unidirectional) and C-Scan. | |
| Graticules | None, Grid (4 sizes 5, 10, 15 and 20% FSH), Polar (4 sizes 5, 10, 15 and 20% FSH) | |
| Offset | Spot Position: Y =-50 to 50, X =-65 to 65% | |
| Digital Spot Position Readout | Display in X,Y or R,θ | |
| Summary | Display of all settings in Legacy Format | |
| Removable Data Storage | Media | Micro SD HC Card 32GB |
| Setup Storage | Over 10,000 settings | |
| Stored Screen Shots | micro SD up to 32GB, holding over 10,000 screen shots | |
| Recorded Data | Over 500 2.5 minute long data recordings. | |
| Guides | 10,000 Slides plus | |
| C-Scan | Max no of C-Scan Data Files 1,000 | |
| Advanced Features | Data Logging | Real-time recording of signal data and Replay on instruments and desktop PC up to 164 seconds |
| Guides | Create and display a slide show containing instructions, tutorials and procedures using Microsoft PowerPoint. | |
| Attachments | Screenshots and Data Recordings are saved in a folder with the name of the Settings. | |
| Loop | Capture a live repetitive signal and then optimize the instrument settings (Phase, Gain, Filters) to simplify optimizing the parameters | |
| Trace | Allows a calibration reference signal to be stored on the screen and then compared with the live signal | |
| Auto Phase | Allows phase angle to be automatically set to a pre-set angle | |
| Scanning | Connector | 8 way LEMO 1b for encoder and scanner control |
| Encoder | 2 phase 2 axis; =X/Y or R-Theta | |
| Automatic | Controls and acquires data from a Stepper Motor Driven XY Scanner | |
| Count Rate Max | 100kHz | |
| C-Scan | Resolution | Max size 1 million data points |
| Scaling | 0.1-999.9 pixels/mm. | |
| Typical Scan | 120 by 100 mm at 0.1mm resolution. | |
| Data Saved | Data stored as XY Pairs for 2 Channels. Data presentation X, Y, R or theta on CH1, Ch2 or Mix. | |
| Outputs | PC Connectivity | Open collector transistor (32v dc at 10mA max) available on 12 way LEMO. |
| Digital Volt Free Alarm | On Lemo 12 way Open collector transistor (36v dc at 10mA max). | |
| VGA | Full 15 way VGA output (EC screens only) | |
| Languages | Selectable from English, French, Spanish, Italian, Portuguese, Russian, Japanese, Chinese, Turkish, Czech, and Norwegian. | |
| Verification Levels | The system includes on delivery a 2 year validity Verification Level 2 detailed functional check and calibration as per ISO 15548-1:2013Power-on self test The system performs a self | |
| Power-on Self Test | The system performs a self test on start up of external ram, sd ram, accelerometer, Micro SD card, LCDscreen buffer. | |
| Power | External | 100-240 v 50-60Hz 30 Watts |
| Battery | Internal 7.2V nominal @ 3100mAh = 22.32 watt.hr | |
| Running Time | Up to 8 hours with a 2MHz Pencil Probe 30% Back Light and up to 6 hours with a Rotary Drive 50% duty cycle. | |
| Charging Time | 2.5 hrs. charge time, Simultaneous charge and operation | |
| Weight Including Internal Battery | 1.3 kg, 2.9 lbs. | |
| Physical | Size (L x W x H) | 5.7" x 2.1 x 9.3" (146 x 53 x 237mm) |
| Material | Aluminum alloy Mg Si 0.5 powder-coated epoxy | |
| Operating Temperature | -4° to 140° F (-20 to 60 °C) | |
| Storage Temperature | Storage for up to 12 months -4° to 95° F (-20 to 35 °C) Nominal 68° F ( 20 °C) | |
| IP Rating | IP54 | |
Standard PhaseCheck Kit Includes
KIPHAS001 PhaseCheck Dual Frequency Eddy Current Portable Flaw Detector with Encoder Input Kit Include
- IPHAS001 Instrument, PhaseCheck, Dual Frequency Eddy Current Portable Flaw Detector with Encoder Input.
AWEL002 Accessory, WeldCheck, Power Adapter Input Plugs (UK, EU, US & Australia)
AWEL003 Accessory, Adjustable Padded Shoulder Strap
AC006 Accessory, Instrument Soft Carry Case, ETher NDE
A090 USB CABLE - A to MINI B, 1m
40865 Quick Reference Card - PhaseCheck
AAER004 Accessory, Protective Splash Proof Cover (WeldCheck2, WeldCheck , AeroCheck2, AeroCheck )
ALL12-L04-015R Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
ALLCX-M02-015A Accessory, Lead, Lemo 00 to Microdot, 1.5m (Vantage/ETi/WeldCheck/AeroCheck)
ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage/ETi/WeldCheck/AeroCheck)
C254 PLUG 6 WAY LEMO FGG.1B.306.CLAD62Z (5.3 - 6.2mm)
C010 CABLE SLEEVE - GMA1B054DN LEMO BLACK
Optional Accessories
- ALL08-L08-025 Lead, Lemo 8-Way - Lemo 8 Way, 2.5m
- ALL08-ENC-002 Encoder to Lemo 8-Way, 2m long (Encoder - Manual Scanning)
- AER002 Hard Transit Case
- 40470 Tripod Bracket - To fit 1/4" Camera Tripod Mount with Male Screw
- AWEL006 External 8 x AA Battery Holder and On/Off Switch
- AWEL007 Wrist Strap
- AWEL008 In-Car Power Adapter
The PhaseCheck share the same features and performance of the AeroCheck Eddy Current Flaw Detector combined with the ability to scan areas and document inspection results using a C-Scan Display and X/Y and R/Theta manual scanners with easy scan calibration. The ETher NDE PhaseCheck can be used with all reflection, bridge and absolute probes from all manufacturers and uses industry standard 12-Way Lemo and Co-axial Lemo 00 connectors, reducing the need to use adapters.
ETher NDE ETi-200 Advanced Eddy Current Flaw Detector - NEW (ETi-200)
Extremely Portable with Advanced Functions
The ETi-200 Eddy Current Flaw Detector is designed to offer advanced multi-frequency and multi-channel flaw detection while offering unmatched flexibility and portability on the market. Appealing to all sectors within NDT, the ETi-200 allows the operator to program not only frequency, but many other advanced functions. In dual-probe mode, the ETi-200 will multiplex four channels per probe whereas in single probe mode up to eight channels are available. A cast aluminum enclosure and protective rubber over-molding make the ETi-200 extremely durable and robust.
Features
Rugged instrument with cast aluminum frame, rubber over-molding and ergonomic design
Great battery life at 5.5 hours with “quick swap” batteries
Removable Eddy Current Cartridge allows easy future upgrades and enhancements
Excellent analogue performance
Advanced Software including signal mixing functions, measurement cursors, configurable alarms and auto-load
Powerful yet compact, weighing just 6.2 lbs. and includes an adjustable hand-strap and harness attachment points
IP54 Protection - splash and dust proof
Large High Definition Display - 7” diagonal 800 x 480 pixel color TFT display with programmable colors
State of the Art Communications and Data Storage - USB, Ethernet port and 32GB SD Card slot
25k sample rate and can store as much as 48 hours of continuous live recordings
User-friendly interface with intuitive ‘Smart Wheel’, direct keys for common functions, customizable panes and clear icons
Designed with end users and the inspection environment in mind
Software
General Settings Screen
Single Channel, Multi-frequency with ID Probe
Single Frequency, Waterfall, Spot, Time-base and Chart Display
Advanced File Management Screen
ETi-200 Specifications
Standard Kit Includes
Optional Accessories
Weld Probe Kits
Surface Probe Kit
Sub Surface Probe Kit
Tube Probe Kit
The ETi-200 Eddy Current Flaw Detector is designed to offer advanced multi-frequency and multi-channel flaw detection while offering unmatched flexibility and portability on the market. Appealing to all sectors within NDT, the ETi-200 allows the operator to program not only frequency, but many other advanced functions. In dual-probe mode, the ETi-200 will multiplex four channels per probe whereas in single probe mode up to eight channels are available. A cast aluminum enclosure and protective rubber over-molding make the ETi-200 extremely durable and robust.
Features
Rugged instrument with cast aluminum frame, rubber over-molding and ergonomic design
Great battery life at 5.5 hours with “quick swap” batteries
Removable Eddy Current Cartridge allows easy future upgrades and enhancements
Excellent analogue performance
Advanced Software including signal mixing functions, measurement cursors, configurable alarms and auto-load
Powerful yet compact, weighing just 6.2 lbs. and includes an adjustable hand-strap and harness attachment points
IP54 Protection - splash and dust proof
Large High Definition Display - 7” diagonal 800 x 480 pixel color TFT display with programmable colors
State of the Art Communications and Data Storage - USB, Ethernet port and 32GB SD Card slot
25k sample rate and can store as much as 48 hours of continuous live recordings
User-friendly interface with intuitive ‘Smart Wheel’, direct keys for common functions, customizable panes and clear icons
Designed with end users and the inspection environment in mind
Software
General Settings Screen
Single Channel, Multi-frequency with ID Probe
Single Frequency, Waterfall, Spot, Time-base and Chart Display
Advanced File Management Screen
ETi-200 Specifications
| Probe | |
| Modes | Lemo 00 for absolute probes and a 12 way Lemo connection for Reflection, Bridge and Rotary and Second Lemo 12 way for Reflection and Bridge Probes. Absolute and Bridge modes selectable at 50 or 100 ohm |
| Test | Up to 8 channels with 12 user definable mixers |
| Frequency | 10 Hz-15 MHz in 0.01 increments per Hz, kHz or MHz range |
| Drive | 0.10 - 20.00v pk-pk in 0.01v increments |
| Signal | |
| Phase | 0°-359.9° in 0.1° increments |
| Gain | Gain: -12.0 - 100 dB in 0.1 steps |
| X/Y Axis Spread | Any valid gain value on either channel. With lockable relative values |
| Digitizing Rate | 36 kHz max above 300kHz drive frequency |
| Filter | Band Pass, High Pass and Low Pass |
| Load | Automatic load selection for absolute probes with manual override. 8 values 1.3 uH to 470 uH |
| Display | |
| Screen | 7” 480 by 800 Pixel Colour TFT |
| Mode | Impedance (phase) plane display with strip chart or time base 1, 2 or 4 panes |
| Grid | Options of; None, 20% (5 by 5), 10% (10 by 10) and Polar |
| Spot Position | /- 50 % in 1% increments |
| Persistence | Permanent and 0.01 -100.00 seconds in 0.1s increments |
| External | Standard 15 way d-type for external monitor, head up display or projector |
| Alarm | |
| Type | 1 per channel selectable; Box or Sector |
| Setting | In increments of 1 % |
| Quantity | 8 |
| Action | Audio and / or signal freeze |
| Data Storage | |
| Settings | Diverse options to internal ram drive, removable SD card (up to 32GB) or USB memory stick (up to 32GB) |
| Recording | Digitised data may be saved to internal memory (up to 32GB), external USB device or SD Card (up to 32GB). 1 GB of Internal Flash Memory. At a 25kHz processing rate, 1 minute of single channel data uses 11MB |
| User Interface | |
| Front Panel | Rotary control, cursor control, 18 push button keys. 4 Status LEDs |
| Software | Tabs, Soft Keys, Scrollable values, Direct data entry, will operate with USB Keyboard |
| Data Output Interface | USB (on the go), Ethernet, SD Card, VGA |
| Enclosure | |
| Dimensions (HxLxW) | 7.9” x 9.0” x 3.0” (20.0 x 22.5 x 7.5 cm) |
| Weight | 6.2 lbs. (2.8 kg) |
| Environmental | IP54 |
| Temperature | Maximum Operating: 0 to 35 °C Recommended Storage: -20 to 70 °C |
| Power | |
| Internal Battery | Replaceable Li-Ion 14.4 v 5.5 hours max life |
| External AC | Power/charger 100-240 v 1.2A ac 50-60 Hz 90 watts |
Standard Kit Includes
KIETI002 ETi 200, Two Channel, Eddy Current Flaw Detector Kit Includes
- IETI002 - Instrument, Eti 200-Two Channel, Eddy Current Lfaw Detector, Multi Frequency 10Hz-15MHz, Gain 0-100db, Lemo 12-Way, Manual on USB Stick and Carry Strap
- AETI001 - Accessory, Hard Transit Case with foam inserts (Eti 100 200)
- AETI002 - Accessory, ETi 100 200 AC Power Adapter (Class 1 Triangular Connector) Input:100-240V - 47-63Hz 1.2A MAX Output: 24V 3.75A
- A123 LEAD, MINI-B (MALE) USB OTG (On the Go) Cable, to USB-A (FEMALE),20cm.
- 40357 ETi Quick Reference Card
- AMXXX ACCESSORY, MAINS LEAD, 2m, Class 1 Triangular Connector, (Per Country of Destination)
- ALL12-L04-015R Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-M02-015A Accessory, Lead, Lemo 00 to Microdot, 1.5m (Vantage)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AALCX-B02S Accessory, Adapter, Lemo00 to BNC Jack (Short) (Lemo 00 to BNC)
Optional Accessories
- AM001 ACCESSORY, MAINS LEAD, UK PLUG, 2m, 250V, 2.5A.(Class 1 Triangular Connector)
- AM002 ACCESSORY, MAINS LEAD, EUROPEAN PLUG, 2m, 250V, 2.5A. (Class 1 Triangular Connector)
- AM003 ACCESSORY, MAINS LEAD, USA PLUG, 2m. (Class 1 Triangular Connector)
- AM004 ACCESSORY, MAINS LEAD, AUSTRALIA PLUG, 2m. (Class 1 Triangular Connector)
- AM005 ACCESSORY, MAINS LEAD, JAPAN PLUG, 2m. (Class 1 Triangular Connector)
Weld Probe Kits
KAWEL001 Weld Probe Accessories Kit Includes
- PWM100S00 Probe, Weld, Dia 16.00mm (Medium) 100kHz, Straight, Disconnect
- PUB100K Probe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC
- ATBW Accessory. Test Block, Weld Probe, Ferrous (Steel EN1A) x4 0.5mm Shims, 0.5, 1.0, 2.0mm slots
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
KAWEL002 Advanced Weld Probe Accessories Kit Includes
- PWS100S000 Probe, Weld, Dia 11.00mm (Small) 100kHz, Straight, Disconnect
- PWM100S00 Probe, Weld, Dia 16.00mm (Medium) 100kHz, Straight, Disconnect
- PUB100K Probe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC
- ATB016 Accessory, Test Block WeldCheck Demo Crack Specimen -
- Plate with two cracks, Type A and C - Toe and Cap
- Plates are 5" x 5", 1/4" thick with false ground crown.
- Standard crack size 1/4" Long x 0.040" deep.
- ATBW Accessory. Test Block, Weld Probe, Ferrous (Steel EN1A) x4 0.5mm Shims, 0.5, 1.0, 2.0mm slots
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
KAWEL004 Weld Probes Accessories, Enhanced AL & SS Inspection Kit Includes
- PWS106S000 Probe, Weld, Dia 11.00mm (Small) 100-600kHz, Multi-surface, Straight, Disconnect
- PUB100K Probe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC
- ATBW Accessory. Test Block, Weld Probe, Ferrous (Steel EN1A) x4 0.5mm Shims, 0.5, 1.0, 2.0mm slots
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
Surface Probe Kit
KASUR001 Surface Inspection Kit Includes
- PU500PSFE/NFE Probe, Unshielded, 500kHz, Fe/NFe, Plastic Handle, Straight, 100mm Long
- PS002PS028-114N Probe, Shielded, 2MHz, Plastic Handle, Straight, 28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)
- PS500PD064-114N Probe, Shielded, 500kHz, Plastic Handle, Double Crank, 6.4 (0.25") Tip Length (Total Length 114mm, 4.5") (15deg Crank, 90deg tip Shank)
- PS002PD064-114N Probe, Shielded, 2MHz, Plastic Handle, Double Crank, 6.4 (0.25") Tip Length (Total Length 114mm, 4.5") (15deg Crank, 90deg tip Shank)
- PK065002NFE Probe, Knife, 65 deg, 2MHz, NFe, Unshielded
- ALLCX-M02-015A Accessory, Lead, Lemo 00 to Microdot, 1.5m (Vantage/ETi)
- ATBF Accessory. Test Block, Ferrous (Steel EN1A), 0.2, 0.5, 1.0mm slots
- ATBA Accessory. Test Block, Aluminum Alloy 7075-T6, 0.2, 0.5, 1.0mm slots
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
Sub Surface Probe Kit
KASUBS001 Sub Surface, Low Frequency Inspection Kit Includes
- PUS16 Probe, Surface, Straight, Dia 16mm, 300Hz - 100KHz, Plastic, Lemo 4-Way
- PUR11 Probe, Surface, Right Angled, Dia 11mm, 300Hz - 100KHz, Plastic, Lemo 4-Way
- ALL12-L04-015R Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ATB001 Accessory, Test Block, Aluminum 7075-T6, 1.6mm Thick, x4 Flat Bottom Holes 75%(1.2mm), 50%(0.8mm), 25%(0.4mm), 12.5%(0.2mm), Deep.
Tube Probe Kit
KATUB001 Tube Inspection Kit Includes
- PID138D0018K Probe, Internal Diameter, Differential, Dia 13.80, Dis-connect, 18k.
- CIDL03F Accessory, ID Lead,12-Way Lemo, Flexible, 3.0m
- ATBTB1587 Accessory, Test Block, Tube, Brass, OD 5/8" , (15.87mm) x 20swg, Calibration Tube
- ATB010 Accessory, Test Block, ID Probe Support Ring OD 25.4 x ID 16.6 x 20.00mm Long
The ETi-200 Eddy Current Flaw Detector is designed to offer advanced multi-frequency and multi-channel flaw detection while offering unmatched flexibility and portability on the market. Appealing to all sectors within NDT, the ETi-200 allows the operator to program not only frequency, but many other advanced functions. In dual-probe mode, the ETi-200 will multiplex four channels per probe whereas in single probe mode up to eight channels are available. A cast aluminum enclosure and protective rubber over-molding make the ETi-200 extremely durable and robust.
ETher NDE ETi-300 Advanced Eddy Current Flaw Detector - NEW (ETi-300)
The ETi-300 is an advanced eddy current tube testing instrument for inspecting non-ferrous tubing from the inner diameter (ID), developed by ETher NDE to perform in the most demanding of environments whilst delivering outstanding inspection results and reporting functionality.
Eddy Current testing has long been acknowledged as the fastest, most efficient and effective inspection method to inspect the large quantity of non-ferrous tubes present in a typical heat exchanger. The ETi-300 instrument and it’s suite of analysis and reporting software is ideal for heat exchanger and condenser inspection applications within Power Generation, Transportation, Petrochemical and Oil and Gas industries.
The ETi-300 and Ether’s suite of software solutions deliver an advanced end to end solution for tube inspectors. Realising that the inspection process is more than just recording data the ETi-300 was conceived to be work with a software suite of solutions, improving on-site workflow and delivering rapid and accurate reporting.
As part of the Tube Inspection suite of solutions we offer:
TMR Mapping which allows tube map templates to be created to enable inspection planning using either photographs, drawings or rapid manual entry
ETherMap is the Data Analysis software for the ETi-300
TMR Reporting processes the analysed data and turns it into a meaningful and informative report.
ETherMap
Data Analysis & User interface
ETherMap is not only the data analysis tool but also the main user interface to the head-less (no screen) instrument. This versatile software developed to be directly connected to our latest instruments where it can control and receive live inspection data in the field, or work with previously recorded data. EtherMap is an intuitive user interface for the ETi 300 operator, capable of processing and analysing data on its own or as an integral part of our end-to-end offering with TMR. When integrated with TMR the user can go all the way from Tube Map design, inspection, analysis to report generation.
Inspection planning with TMR ET*
Advanced Tube Mapping Software
In order to offer the best user experience when it comes to tube map design and report generation Ether NDE have teamed up with Talcyon Pte Ltd, to deliver advanced Tube Mapping Software (TMR) which is second to none in its features and ease-of-use. Tube Mapping Software (TMR) is a solution intuitively designed with the operator and tube inspection task in mind; specifically to produce an accurate layout and labelling of tubes on a tube sheet. Upload a photograph or schematic diagram of the tube sheet and create a map of the tube sheet, assign a number to each of the tube openings. The “tube sheet” presents the software with a graphic representation, which helps to track which tubes have already been measured, aiding efficient workflow, labelled and mapped.
Probes
ID Bobbin Probes
Ether NDE design and manufacture a wide range of ID (Internal Diameter) Differential Bobbin probes:
Probe diameters from 7.5 to 150mm, available in 0.1mm steps
Dis-connectable and integral probe cables
Cable lengths from 3 to 30 metres
Frequency range from 2.7 kHz to 1MHz, centre frequencies 2.7, 10, 24, 76, 190, 400kHz
Eddy Current testing has long been acknowledged as the fastest, most efficient and effective inspection method to inspect the large quantity of non-ferrous tubes present in a typical heat exchanger. The ETi-300 instrument and it’s suite of analysis and reporting software is ideal for heat exchanger and condenser inspection applications within Power Generation, Transportation, Petrochemical and Oil and Gas industries.
The ETi-300 and Ether’s suite of software solutions deliver an advanced end to end solution for tube inspectors. Realising that the inspection process is more than just recording data the ETi-300 was conceived to be work with a software suite of solutions, improving on-site workflow and delivering rapid and accurate reporting.
As part of the Tube Inspection suite of solutions we offer:
TMR Mapping which allows tube map templates to be created to enable inspection planning using either photographs, drawings or rapid manual entry
ETherMap is the Data Analysis software for the ETi-300
TMR Reporting processes the analysed data and turns it into a meaningful and informative report.
ETherMap
Data Analysis & User interface
ETherMap is not only the data analysis tool but also the main user interface to the head-less (no screen) instrument. This versatile software developed to be directly connected to our latest instruments where it can control and receive live inspection data in the field, or work with previously recorded data. EtherMap is an intuitive user interface for the ETi 300 operator, capable of processing and analysing data on its own or as an integral part of our end-to-end offering with TMR. When integrated with TMR the user can go all the way from Tube Map design, inspection, analysis to report generation.
Inspection planning with TMR ET*
Advanced Tube Mapping Software
In order to offer the best user experience when it comes to tube map design and report generation Ether NDE have teamed up with Talcyon Pte Ltd, to deliver advanced Tube Mapping Software (TMR) which is second to none in its features and ease-of-use. Tube Mapping Software (TMR) is a solution intuitively designed with the operator and tube inspection task in mind; specifically to produce an accurate layout and labelling of tubes on a tube sheet. Upload a photograph or schematic diagram of the tube sheet and create a map of the tube sheet, assign a number to each of the tube openings. The “tube sheet” presents the software with a graphic representation, which helps to track which tubes have already been measured, aiding efficient workflow, labelled and mapped.
Probes
ID Bobbin Probes
Ether NDE design and manufacture a wide range of ID (Internal Diameter) Differential Bobbin probes:
Probe diameters from 7.5 to 150mm, available in 0.1mm steps
Dis-connectable and integral probe cables
Cable lengths from 3 to 30 metres
Frequency range from 2.7 kHz to 1MHz, centre frequencies 2.7, 10, 24, 76, 190, 400kHz
Report Creation with TMR ET*
Automated Report Creation
A fast reporting software designed to manage data gathered from inspections, with the capability to present inspection data in easy-to-read formats. Reports are generated with using simple user interface, whilst fully-customisable reporting and output is easily configurable. Report templates are viable to save time and can be built and populated by simply placing elements using a “drag and drop”method. Bespoke and unique reports can be delivered using the report building software features to customise your reports.
Advantages
- Two probe inputs and four frequency channels are available
- An all-in-one end-to-end tube inspection solution
- High-impact-resistant aluminum enclosure
- Developed to satisfy IP66 requirements
- Superior battery life exceeding 12 hours
- Availability of adapters for competitor probes
- Two years of warranty as standard, and an extension until five years available with EtherCover
Features
- Eddy current operating modes
- Eddy current single-probe frequency
- Eddy current dual-probe frequency
- Eddy current one probe up to four channels (for example, three frequencies bridge differential and one frequency absolute; or two frequencies bridge differential and two frequencies absolute)
- Eddy current two probe up to two channels each (for example, dual-probe each with dual-frequency bridge differential)
- TMR Automated Reporting software is user-friendly and customizable
- TMR Tube Mapping software maps from schematics or photographs
- ETherMap intuitive user interface for tube inspection data capture
Accessories
Part Number Item ALL12-Z04SB Accessory, Adapter, 12-Way Lemo to 4-Way Amphenol (ZETEC Bridge Probes) ALL12-J06P Accessory, Adapter, 12-Way Lemo to 6-Way Jaeger (HOCKING Bridge/Reflection Probes)
ETi-300 SPECIFICATION :
Operating
Modes
Eddy Current
Modes
Eddy Current Single Probe Frequency
Eddy Current Dual Probe Frequency
Eddy Current 1 Probe up to 4 Channels (e.g. 3 Frequencies Bridge Differential and 1 Frequency
Absolute or 2 Frequencies Bridge Differential and 2 Frequencies Absolute).
Eddy Current 2 Probe up to 2 Channels each (e.g. Dual Probe each with Dual Frequency Bridge
Differential).
Probe
Connectors
12-Way LEMO 2B (Absolute, Bridge, Reflection, Rotary)
12-Way LEMO 2B (Bridge, Reflection)
BNC - Absolute
Simultaneous probe operation possible using x2 LEMO 12 way
Rotary 600-3000 rpm. ETher Mercury Drive (ADR002), Hocking 33A100, Rohmann MR3, SR1 and SR2
Drive (special adapter needed)
Frequency Multi-Frequency 10Hz - 12.8MHz (no limit on frequency, all channels)
Gain
Overall -18 to 104dB, 0.1, 1 and 6dB steps
Input 0dB or 12dB
Drive 0dB, 6dB and 10dB (0dB reference 1mW into 50 ohm).
Max X/Y Ratio /-100.0 dB
Phase Range 0.0-359.9°, 0.1° steps
Filters
Sample Rate Constant 16kHz overall over 4 times X/Y pairs
High Pass DC to 2kHz or Low Pass Filter, which ever is lower in 1Hz steps. Plus variable adaptive balance
drift compensation 0.01 - 0.5 Hz (6 steps).
Low Pass 1Hz to 4kHz or a quarter of the lowest test frequency, which ever is lower in 1 Hz steps.
Balance
Load
Manual 14 internal balance loads; 2.2µH, 6.0µH, 7.0µH, 8.2µH, 12µH, 15µH, 18µH, 22µH, 30µH, 47µH,
82µH, 330µH, 820µH and 3,300µH
Automatic Optimised balance load selection.
Mix Channel
Frequency Full frequency range available on all channels
Number of
Mixers 8 maximum user definable configuration.
operations Automatic or Manual
Mix Gain X/Y -18 to 18dB
Mix Phase 0.0-359.9°, 0.1° steps
Connectivity
USB Full speed USB 2.0 12.5 MB/s
I/O 8 way LEMO 4 configurable TTL Level with 5v eg encoder input
Power
External 100-240 v 50-60Hz 30 Watts
Battery Internal 7.2V nominal @ 3100mAh = 22.32 watt.hr
Running Time Up to 15 hours with a 2MHz Pencil Probe 30%, up to 8 hours with a Rotary Drive 50% duty cycle.
Charging Time 2.5 hrs. charge time, Simultaneous charge and operation
Power On Selftest The systems performs a self-test on start up.
Physical
Weight Including
Internal Battery 2.8kg (6.17lbs)
Size (w x h x d) 214 x 90 x 342 mm (8.5 x 3.6 x 13.5 inches)
Material High impact-resistant Aluminium enclosure with tough silicon elastomer edge protection.
Operating
Temperature -20 to 60 °C (-5 to 140°F)
Storage
Temperature Storage for up to 12 months -20 to 35 °C (-5 to 95°F). Nominal 20°C (68°F)
IP Rating IP66
Verification Level The system includes on delviery a 2 year validity Verification Level 2, detailed function check and
calibration as per ISO 15548-1:2013
The ETi-300 is an advanced eddy current tube testing instrument for inspecting non-ferrous tubing from the inner diameter (ID), developed by ETher NDE to perform in the most demanding of environments whilst delivering outstanding inspection results and reporting functionality. Eddy Current testing has long been acknowledged as the fastest, most efficient and effective inspection method to inspect the large quantity of non-ferrous tubes present in a typical heat exchanger. The ETi-300 instrument and it’s suite of analysis and reporting software is ideal for heat exchanger and condenser inspection applications within Power Generation, Transportation, Petrochemical and Oil and Gas industries.
ETher NDE SteelCheck Steel Tube Inspection - NEW (SteelCheck)
Portable, Rugged & Battery Operated
The SteelCheck is an affordable, battery operated, portable 3 channel(Hall Sensor and 2 coil) tube inspection unit for Carbon Steel (Ferromagnetic Tubes) using Magnetic Flux Leakage. Unlike other remote field eddy current method it is unaffected by external Aluminum Fins and has the capability to discriminate between external and internal defects.
Features
Dedicated single method tube inspection instrument for the identification of OD, ID Defects and Wall Thinning.
A 3 channel (Hall Sensor and 2 coil) tube inspection unit for Carbon Steel (Ferromagnetic Tubes) using Magnetic Flux Leakage
Ideal for ferrous tubing, especially fin-fan tubes
Industry standard 12-Way Lemo and Co-axial Lemo 00 connectors
Intuitive user friendly interface, single level menu system, "quick function" sidebar
Display Modes: Time base (0.1-20 seconds, StripChart and Waterfall)
Internal data logging system, PC application for desktop reporting
5.7" (145mm) large daylight readable display
Compact, rugged site proven housing - 2.6 lbs. (1.2kg)
8 hrs. battery life on one charge
2 year standard warranty
Optional ETherCover extending warranty to 5 years
SteelCheck Specifications
Standard Kit Includes :
SteelCheck Instrument
Soft Carrying Case
Charger
Manual on USB
Additional Accessories :
PMFL187-20L10: Probe for 1˝ (2.5cm) 12 AWG with 65ft. (20m) push pull cable.
ATBTC-254-12SWG: Calibration tube for 1˝ (2.5cm) 12 AWG tube.
PMFL198-20L10: Probe for 1˝ (2.5cm) 14 AWG with 65ft. (20m) push pull cable.
ATBTC-254-14SWG: Calibration tube for 1˝(2.5cm) 14 AWG tube.
Weld Probe Kits
The SteelCheck is an affordable, battery operated, portable 3 channel(Hall Sensor and 2 coil) tube inspection unit for Carbon Steel (Ferromagnetic Tubes) using Magnetic Flux Leakage. Unlike other remote field eddy current method it is unaffected by external Aluminum Fins and has the capability to discriminate between external and internal defects.
Features
Dedicated single method tube inspection instrument for the identification of OD, ID Defects and Wall Thinning.
A 3 channel (Hall Sensor and 2 coil) tube inspection unit for Carbon Steel (Ferromagnetic Tubes) using Magnetic Flux Leakage
Ideal for ferrous tubing, especially fin-fan tubes
Industry standard 12-Way Lemo and Co-axial Lemo 00 connectors
Intuitive user friendly interface, single level menu system, "quick function" sidebar
Display Modes: Time base (0.1-20 seconds, StripChart and Waterfall)
Internal data logging system, PC application for desktop reporting
5.7" (145mm) large daylight readable display
Compact, rugged site proven housing - 2.6 lbs. (1.2kg)
8 hrs. battery life on one charge
2 year standard warranty
Optional ETherCover extending warranty to 5 years
SteelCheck Specifications
| Probe | Connector | 10way LEMO 2B |
| Channels | 1 Hall Effect Sensor, 2 coils | |
| Construction | Stainless Steel / Titanium | |
| Max Pull | 100 kg | |
| Longevity | Greater than 1000 tubes | |
| Gain | Channels | 3 independent channels with gain lock |
| Range | Gain adjustable 0 to 72dB | |
| Increments | 0.1, 1 and 6 dB Steps | |
| Data Conversion | Bit Depth | 12bit |
| Sample Rate | 5kHz | |
| Dynamic Range | 40dB | |
| Filters | Normal High Pass | DC to 1kHz |
| Normal Low Pass | 5 to 1kHz | |
| Alarms | Level | Fully configurable, Freeze, Tone or visual |
| Display | Type | 24bit color, daylight readable, 5.7" (14.5cm) screen |
| Viewable Area | Horizontal x Vertical - 4.6" x 3.4" (115.2 x 86.4mm) | |
| Resolution (pixels) | 640 x 480 | |
| Configurable Screen | Full Screen, up to 4 panes with variable function | |
| Display Modes | Time base (0.1-20 seconds, Stripchart and Waterfall) | |
| Graticules | None, Grid (4 sizes: 5, 10, 15 at 20% FSH) | |
| Offset | Trace Position: ± 150% | |
| Storage | Setup | Micro SD up to 32GB, storing over 10,000 settings |
| Stored Screen Shots | Micro SD up to 32GB, storing over 10,000 settings | |
| Inspect | Comprehensive Record, Replay and Storage | |
| Outputs | PC Connectivity | USB (Full PC remote control plus Real Time) |
| VGA | Full 15 way VGA output | |
| Languages | English. Others to follow | |
| Power | External | 100-240VAC, 50-60Hz, 700mA |
| Battery | Internal 8.4 V @ 3200mAh | |
| Running Time | 100% backlight over 8hrs. Over 10.5 hrs. with 40% backlight | |
| Charging Time | 2.5 hrs. charging time. Simultaneous charge and operation | |
| Physical | Weight | 2.7 lbs. (1.2 kg) |
| Size (W x H x D) | 9.4" x 5.7" x 2.1" (237.5 x 144 x 52 mm) | |
| Material | Aluminum Alloy Mg Si 0.5 powder coated | |
| Operating Temperature | -4° to 140°F (-20° to 60°C) | |
| Storage Temperature | Storage for up to 12 months. -4° to 95°F (-20° to 35°C). Nominal 68°F (20°C) | |
| IP Rating | IP54 |
SteelCheck Instrument
Soft Carrying Case
Charger
Manual on USB
Additional Accessories :
PMFL187-20L10: Probe for 1˝ (2.5cm) 12 AWG with 65ft. (20m) push pull cable.
ATBTC-254-12SWG: Calibration tube for 1˝ (2.5cm) 12 AWG tube.
PMFL198-20L10: Probe for 1˝ (2.5cm) 14 AWG with 65ft. (20m) push pull cable.
ATBTC-254-14SWG: Calibration tube for 1˝(2.5cm) 14 AWG tube.
Weld Probe Kits
KAWEL001 Weld Probe Accessories Kit Includes
- PWM100S00 Probe, Weld, Dia 16.00mm (Medium) 100kHz, Straight, Disconnect
- PUB100K Probe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC
- ATBW Accessory. Test Block, Weld Probe, Ferrous (Steel EN1A) x4 0.5mm Shims, 0.5, 1.0, 2.0mm slots
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
KAWEL002 Advanced Weld Probe Accessories Kit Includes
- PWS100S000 Probe, Weld, Dia 11.00mm (Small) 100kHz, Straight, Disconnect
- PWM100S00 Probe, Weld, Dia 16.00mm (Medium) 100kHz, Straight, Disconnect
- PUB100K Probe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC
- ATB016 Accessory, Test Block WeldCheck Demo Crack Specimen -
- Plate with two cracks, Type A and C - Toe and Cap
- Plates are 5" x 5", 1/4" thick with false ground crown.
- Standard crack size 1/4" Long x 0.040" deep.
- ATBW Accessory. Test Block, Weld Probe, Ferrous (Steel EN1A) x4 0.5mm Shims, 0.5, 1.0, 2.0mm slots
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
KAWEL004 Weld Probe Accessories, Enhanced AL & SS Inspection Kit Includes
- PWS106S000 Probe, Weld, Dia 11.00mm (Small) 100-600kHz, Multi-surface, Straight, Disconnect
- PUB100K Probe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC
- ATBW Accessory. Test Block, Weld Probe, Ferrous (Steel EN1A) x4 0.5mm Shims, 0.5, 1.0, 2.0mm slots
- ALL12-L04-015B Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-B02-015A Accessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
KASUR001 Surface Inspection Kit Includes
- PU500PSFE/NFE Probe, Unshielded, 500kHz, Fe/NFe, Plastic Handle, Straight, 100mm Long
- PS002PS028-114N Probe, Shielded, 2MHz, Plastic Handle, Straight, 28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)
- PS500PD064-114N Probe, Shielded, 500kHz, Plastic Handle, Double Crank, 6.4 (0.25") Tip Length (Total Length 114mm, 4.5") (15deg Crank, 90deg tip Shank)
- PS002PD064-114N Probe, Shielded, 2MHz, Plastic Handle, Double Crank, 6.4 (0.25") Tip Length (Total Length 114mm, 4.5") (15deg Crank, 90deg tip Shank)
- PK065002NFE Probe, Knife, 65 deg, 2MHz, NFe, Unshielded
- ALLCX-M02-015A Accessory, Lead, Lemo 00 to Microdot, 1.5m (Vantage/ETi)
- ATBF Accessory. Test Block, Ferrous (Steel EN1A), 0.2, 0.5, 1.0mm slots
- ATBA Accessory. Test Block, Aluminum Alloy 7075-T6, 0.2, 0.5, 1.0mm slots
- AW003 Accessory, Butterfly PTFE Tape (Pack of 30)
- AC002 Accessory, Deluxe Probe Case PHDC1
KASUBS001 Sub Surface, Low Frequency Inspection Kit Includes
- PUS16 Probe, Surface, Straight, Dia 16mm, 300Hz - 100KHz, Plastic, Lemo 4-Way
- PUR11 Probe, Surface, Right Angled, Dia 11mm, 300Hz - 100KHz, Plastic, Lemo 4-Way
- ALL12-L04-015R Accessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ATB001 Accessory, Test Block, Aluminum 7075-T6, 1.6mm Thick, x4 Flat Bottom Holes 75%(1.2mm), 50%(0.8mm), 25%(0.4mm), 12.5%(0.2mm), Deep.
KATUB001 Tube Inspection Kit Includes
- PID138D0018K Probe, Internal Diameter, Differential, Dia 13.80, Disconnect, 18k.
- CIDL03F Accessory, ID Lead,12-Way Lemo, Flexible, 3.0m
- ATBTB1587 Accessory, Test Block, Tube, Brass, OD 5/8" , (15.87mm) x 20swg, Calibration Tube
- ATB010 Accessory, Test Block, ID Probe Support Ring OD 25.4 x ID 16.6 x 20.00mm Long
The SteelCheck is an affordable, battery operated, portable 3 channel(Hall Sensor and 2 coil) tube inspection unit for Carbon Steel (Ferromagnetic Tubes) using Magnetic Flux Leakage. Unlike other remote field eddy current method it is unaffected by external Aluminum Fins and has the capability to discriminate between external and internal defects.
ETher NDE WeldCheck Plus Eddy Current Flaw Detector - NEW (WeldCheck Plus)
As an advanced flaw detector for weld inspection the WeldCheck Plus delivers dual channel/frequency capability, Automatic Lift Off Gain Compensation (LOGC) and conductivity measurement, further enhancing the operator's inspection capability in the field. LOGC automatically compensates for coating thickness variations in real time further improving the quality of the inspection results.
“Dual Channel” for weld inspection means the weld probe can simultaneously assess coating thickness and detect defects, increasing operator efficiency and output.
Superior Performance Weld Inspection
Both the WeldCheck and WeldCheck 2 can perform a great many eddy current inspection tasks due to their superior performance, including weld inspection, surface defect detection and low frequency inspection of non-ferrous material.
The WeldCheck 2 is a single channel/frequency instrument that offers a simplified specification but none the less boasts a 10Hz-20MHz frequency range.
The WeldCheck Plus is a dual channel/frequency instrument with conductivity for maximum flexibility, with a frequency range of 10Hz-12.8MHz.
Features
Single or Dual Channel models
Large, Crisp Daylight Readable Display
User Friendly Interface and Ergonomic Lightweight Design
Industry Standard Probe Connectors
8 Hour Battery Life
Rapid 2.5 Hour Charging Time
Three-Year Warranty (6-Year Extended Warranty with ETherCover)
Advanced Features Loop, Guides and Automatic Lift Off Gain Connection
Lightweight, Rugged and Easy to Use
The WeldCheck weighs just 2.6lbs (1.2kg), has a tough metal outer case and is optimized to resist moist atmospheres. It's 8.5 hour battery life and storage of over 500 readings allows field use for an entire shift without interruption. Additionally, the WeldCheck is equipped with an easy to navigate menu system for rapid function access, including 4 programable, quick access "soft keys" to fit your needs.
Works the Way You Do
The WeldCheck series features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Loop, Guides and Trace Features
"Loop" is a convenient function for capturing live repetitive signals and then optimizing the settings in order to simplify the task of optimizing the parameters.
"Guides" allows the user to display a slide show that can be created easily using 3rd party software. Instructions, tutorials, etc. can be added to the WeldCheck quickly so the inspector can easily switch between the Inspection itself and the Guides while performing a live test.
The "Trace" function allows a reference waveform to be stored on the screen alongside the graticule behind the live spot, allowing the operator to readily compare live data with the reference calibration.
Exclusive Features for WeldCheck Plus
"Dual Frequency / Channel Feature" - At different frequencies, different signal indications (e.g. lift off and defect) have a different relative phase and amplitude response. By means of Phase rotation and Gain change of the X Y signal components, one of these indications can be manipulated to be almost identical in phase and amplitude as the other and then by subtraction (mixing), the unwanted component is minimized, giving an improved detection of the required signal.
"Auto-Mix" simplifies the sometimes complex procedure of mixing two different frequency signals and can be achieved on the WeldCheck through a series of easy steps. Once set up, the Auto-mix itself is as simple as pressing one key.
"Conductivity Measurement" - When connecting the Conductivity Probe, the WeldCheck auto-detects the probe and seamlessly switches into conductivity mode. Removal of the probe switches the instrument back to flaw detection mode.
"Automatic Lift Off Gain Compensation" automatically compensates the gain of the defect channel according to the paint thickness thus ensuring that a defect signal will appear the same height irrespective of the paint thickness.
Top-Quality Warranties for Top-Quality Instruments
ETher NDE is unique in that they offer warranty coverage unlike anyone else in the field. All ETher Phase Plane Instruments come with the standard 3-year warranty, which covers all components of the instrument and only excludes customer damage or misuse. However, you can also opt in for an extended 6-year ETherCover warranty plan, putting it truly in a league of its own.
The ETherCover 6-Year Extended Warranty Includes:
Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
One Free of Charge Battery Swap within the six year period (if required)
One Free of Charge Keypad Replacement within the six-year period (if required)
Guaranteed Fast Repair
Free of Charge Software Upgrades within the six year period
ETher NDE WeldCheck Specifications
Conductivity Specification (WeldCheck Only)
Standard WeldCheck Series Kits
Optional Accessories
“Dual Channel” for weld inspection means the weld probe can simultaneously assess coating thickness and detect defects, increasing operator efficiency and output.
Superior Performance Weld Inspection
Both the WeldCheck and WeldCheck 2 can perform a great many eddy current inspection tasks due to their superior performance, including weld inspection, surface defect detection and low frequency inspection of non-ferrous material.
The WeldCheck 2 is a single channel/frequency instrument that offers a simplified specification but none the less boasts a 10Hz-20MHz frequency range.
The WeldCheck Plus is a dual channel/frequency instrument with conductivity for maximum flexibility, with a frequency range of 10Hz-12.8MHz.
Features
Single or Dual Channel models
Large, Crisp Daylight Readable Display
User Friendly Interface and Ergonomic Lightweight Design
Industry Standard Probe Connectors
8 Hour Battery Life
Rapid 2.5 Hour Charging Time
Three-Year Warranty (6-Year Extended Warranty with ETherCover)
Advanced Features Loop, Guides and Automatic Lift Off Gain Connection
Lightweight, Rugged and Easy to Use
The WeldCheck weighs just 2.6lbs (1.2kg), has a tough metal outer case and is optimized to resist moist atmospheres. It's 8.5 hour battery life and storage of over 500 readings allows field use for an entire shift without interruption. Additionally, the WeldCheck is equipped with an easy to navigate menu system for rapid function access, including 4 programable, quick access "soft keys" to fit your needs.
Works the Way You Do
The WeldCheck series features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Loop, Guides and Trace Features
"Loop" is a convenient function for capturing live repetitive signals and then optimizing the settings in order to simplify the task of optimizing the parameters.
"Guides" allows the user to display a slide show that can be created easily using 3rd party software. Instructions, tutorials, etc. can be added to the WeldCheck quickly so the inspector can easily switch between the Inspection itself and the Guides while performing a live test.
The "Trace" function allows a reference waveform to be stored on the screen alongside the graticule behind the live spot, allowing the operator to readily compare live data with the reference calibration.
Exclusive Features for WeldCheck Plus
"Dual Frequency / Channel Feature" - At different frequencies, different signal indications (e.g. lift off and defect) have a different relative phase and amplitude response. By means of Phase rotation and Gain change of the X Y signal components, one of these indications can be manipulated to be almost identical in phase and amplitude as the other and then by subtraction (mixing), the unwanted component is minimized, giving an improved detection of the required signal.
"Auto-Mix" simplifies the sometimes complex procedure of mixing two different frequency signals and can be achieved on the WeldCheck through a series of easy steps. Once set up, the Auto-mix itself is as simple as pressing one key.
"Conductivity Measurement" - When connecting the Conductivity Probe, the WeldCheck auto-detects the probe and seamlessly switches into conductivity mode. Removal of the probe switches the instrument back to flaw detection mode.
"Automatic Lift Off Gain Compensation" automatically compensates the gain of the defect channel according to the paint thickness thus ensuring that a defect signal will appear the same height irrespective of the paint thickness.
Top-Quality Warranties for Top-Quality Instruments
ETher NDE is unique in that they offer warranty coverage unlike anyone else in the field. All ETher Phase Plane Instruments come with the standard 3-year warranty, which covers all components of the instrument and only excludes customer damage or misuse. However, you can also opt in for an extended 6-year ETherCover warranty plan, putting it truly in a league of its own.
The ETherCover 6-Year Extended Warranty Includes:
Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
One Free of Charge Battery Swap within the six year period (if required)
One Free of Charge Keypad Replacement within the six-year period (if required)
Guaranteed Fast Repair
Free of Charge Software Upgrades within the six year period
ETher NDE WeldCheck Specifications
| ETher NDE WeldCheck Specifications | ||
| Probe | WeldCheck 2 | WeldCheck |
| Connectors | 12 Way Lemo 2b (Absolute, Bridge and Reflection) and Connection Lemo 00 (for single element absolute probes). | Simulataneous probe operation possile using Lemo 12 way and Lemo 00 |
| Frequency | Single Freq. = 10Hz - 20MHz with range variable resolution | Dual Freq. = 10Hz - 12.8MHz |
| Gain | ||
| Overall | -18 to 100 dB, 0.1, 1 and 6dB steps (100dB maximum) | |
| Input | 0dB or 12dB | |
| Drive | 0dB, 6dB and 10dB (0dB reference 1mW into 50 ohm) | |
| Max X/Y Ratio | /-100.0 dB | |
| Phase | ||
| Range | 0.0-359.9°, 0.1° steps | |
| Auto Phase | Allows phase angle to be automatically set to a pre set angle | |
| Filters | ||
| Normal High Pass | DC to 2kHz or Low Pass Filter, which ever is the lower in 1 Hz steps. Plus variable adaptive balance drift compensation 0.01 - 0.5 Hz (6 steps) | |
| Normal Low Pass | 1Hz to 2kHz or a quarter of the lowest test frequency, which ever is lower in 1 Hz steps | |
| Balance | ||
| Manual | 14 internal balance loads; 2.2μH, 5.0μH, 6.0μH, 6.5μH, 7.0μH, 7.5μH, 8.2μH, 12μH, 15μH, 18μH, 22μH, 30μH, 47μH, 82μH | |
| Automatic | Optimized balance load selection | |
| Alarms | ||
| Box | Fully configurable, Freeze, Tone or visual | |
| Sector | Fully configurable, Freeze, Tone or visual | |
| Output | Open collector transtor (50v dc at 10mA max) available on 12 way lemo | |
| Display | ||
| Type | 5.7” (145mm), 18 bit Color, daylight readable | |
| Viewable Area | 115.2mm (Horizontal) x 86.4mm (Vertical) | |
| Resolution | 640 x 480 pixels | |
| Flip | Manual or automatic screen orrientation change to enable left or right handed use | |
| Color Schemes | User configurable Dark, Bright and Black & White | |
| Configurable Screen | Full Screen, Single, Dual Spot or Dual Pane with variable size and location and function e.g. XY, Timebase, Waterfall and Meter | |
| Display Modes | Spot, Time base (0.1-20 seconds x 1-200 sweeps and up to 55 seconds), Waterfall and Meter with peak hold and % readout | |
| Graticules | None, Grid (4 sizes 5, 10, 15 and 20% FSH), Polar (4 sizes 5, 10, 15 and 20% FSH) | |
| Offset | Spot Position: Y =-50 to 50, X =-65 to 65% | |
| Digital Spot | Display in X,Y or R,θ | |
| Position Readout Summary | Display of all settings in Legacy Format | |
| Removable Data Storage | ||
| Setup Storage | micro SD up to 32GB, holding over 10,000 settings | |
| Stored Screen | micro SD up to 32GB, holding over 10,000 screen shots | |
| Shots | Comprehensive Record Replay and Storage | |
| Record Replay | Real-time recording of trace data and Replay on instruments and desktop PC up to 164 seconds | |
| Outputs | ||
| PC Connectivity | USB (Full PC remote control plus Real Time data) | |
| Digital Volt Free Alarm | On Lemo 12 way Open collector transistor (36v dc at 10mA max). | |
| VGA | Full 15 way VGA output | |
| General | ||
| Languages | English, French, Spanish, Russian, Japanese, Chinese, Turkish | |
| Verification Level | The system includes on delivery a 2 year validity Verification Level 2 detailed functional check and calibration as per ISO 15548-1:2013 | |
| Power on Self Test | The system performs a self test on start up of external ram, sd ram, accelerometer, Micro SD card, LCD screen buffer | |
| Power | ||
| External | 100-240 v 50-60Hz 30 Watts | |
| Battery | Internal 7.2V nominal @ 3100mAh = 22.32 watt.hr | |
| Running Time | Up to 8 hours with a 2MHz Pencil Probe 30% Back Light and up to 6 hours with a Rotary Drive at 3000rpm 50% duty cycle | |
| Charging Time | 2.5 hrs. charge time, Simultaneous charge and operation | |
| Physical | ||
| Weight | 1.2 kg, 2.7 lbs | |
| Size (WxHxD) | 237.5mm x 144mm x 52mm / 9.4” x 5.7” x 2.1” | |
| Material | Aluminum alloy Mg Si 0.5 powder-coated | |
| Operating Temp | -20 to 60 °C | |
| Storage Temp | Storage for up to 12 months -20 to 35 °C Nominal 20 °C | |
| IP Rating | 54 | |
Conductivity Specification (WeldCheck Only)
| WeldCheck Conductivity Specification | |
| Frequency | One frequency only 60kHz standard (choice of 120, 240 and 480kHz) |
| Accuracy | 0.5%-10% IACS better than /-0.05% IACS 10%-25% IACS better than /-0.25% IACS 25%-60% IACS better than /-0.5% IACS 60%-110% IACS better than /-1% IACS Lift Off corrected to 1.0mm No temperature compensation All Errors at 90% Confidence Level |
| Resolution | 3 decimal points max Auto Resolution Mode AutoS = Legacy Instrument, Auto = SigmaCheck |
Standard WeldCheck Series Kits
KIWEL003 Kit, WeldCheck2, Eddy Current Portable Flaw Detector, Including:
- IWEL003 Instrument, WeldCheck2, Single Frequency, (10Hz-12.8MHz) Hand Held, Portable Flaw Detector. Software Manual on USB Stick
- AWEL002 AeroCheck, Power Adapter Input Plugs (UK, EU, US & Australia)
- AWEL003 Adjustable Shoulder Strap, Padded with Quick-Release
- AC006 Instrument Soft Carry Case
- A090 USB Cable, A to MIN B
- 40463 Quick Reference Card
KIWEL002 Kit, WeldCheck , Eddy Current Portable Flaw Detector, Including:
- IWEL002 Instrument, WeldCheck , Dual Frequency, (10Hz-12.8MHz) Hand Held, Portable Flaw Detector. Software Manual on USB Stick
- AWEL002 AeroCheck, Power Adapter Input Plugs (UK, EU, US & Australia)
- AWEL003 Adjustable Shoulder Strap, Padded with Quick-Release
- AC006 Instrument Soft Carry Case
- A090 USB Cable, A to MIN B
- 40463 Quick Reference Card
- ALLCX-M02-015A Lead, Lemo 00 to Microdot, 1.5m (Absolute)
- ALL12-L04-015R Lead, Lemo 12-Way - Lemo 4-Way (Reflection)
Optional Accessories
- AWEL004 Hard Transit Case
- AAER004 Protective Splash Proof Cover (WeldCheck2, WeldCheck , AeroCheck2, AeroCheck )
- AWEL006 External, 8 x AA Battery Holder with On/Off Switch
- AWEL008 In car Power Adapter
- ALL12-L04-015R Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ALL12-L04-015B Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-M02-015A Lead, Lemo 00 to Microdot, 1.5m (Absolute)
- ALLCX-B02-015A Lead. Lemo 00 to BNC, 1.5m (Absolute)
- 40470 Tripod Bracket To fit 1/4” Camera Tripod Mount with Male Screw
As an advanced flaw detector for weld inspection the WeldCheck Plus delivers dual channel/frequency capability, Automatic Lift Off Gain Compensation (LOGC) and conductivity measurement, further enhancing the operator's inspection capability in the field. LOGC automatically compensates for coating thickness variations in real time further improving the quality of the inspection results.
ETher NDE WeldCheck 2 Eddy Current Flaw Detector - NEW (WeldCheck 2)
Superior Performance Weld Inspection
Both the WeldCheck and WeldCheck 2 can perform a great many eddy current inspection tasks due to their superior performance, including weld inspection, surface defect detection and low frequency inspection of non-ferrous material.
The WeldCheck 2 is a single channel/frequency instrument that offers a simplified specification but none the less boasts a 10Hz-20MHz frequency range.
The WeldCheck is a dual channel/frequency instrument with conductivity for maximum flexibility, with a frequency range of 10Hz-12.8MHz.
Features
Single or Dual Channel models
Large, Crisp Daylight Readable Display
User Friendly Interface and Ergonomic Lightweight Design
Industry Standard Probe Connectors
8 Hour Battery Life
Rapid 2.5 Hour Charging Time
Three-Year Warranty (6-Year Extended Warranty with ETherCover)
Advanced Features Loop, Guides and Automatic Lift Off Gain Connection
Lightweight, Rugged and Easy to Use
The WeldCheck weighs just 2.6lbs (1.2kg), has a tough metal outer case and is optimized to resist moist atmospheres. It's 8.5 hour battery life and storage of over 500 readings allows field use for an entire shift without interruption. Additionally, the WeldCheck is equipped with an easy to navigate menu system for rapid function access, including 4 programable, quick access "soft keys" to fit your needs.
Works the Way You Do
The WeldCheck series features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Loop, Guides and Trace Features
"Loop" is a convenient function for capturing live repetitive signals and then optimizing the settings in order to simplify the task of optimizing the parameters.
"Guides" allows the user to display a slide show that can be created easily using 3rd party software. Instructions, tutorials, etc. can be added to the WeldCheck quickly so the inspector can easily switch between the Inspection itself and the Guides while performing a live test.
The "Trace" function allows a reference waveform to be stored on the screen alongside the graticule behind the live spot, allowing the operator to readily compare live data with the reference calibration.
Exclusive Features for WeldCheck Plus
"Dual Frequency / Channel Feature" - At different frequencies, different signal indications (e.g. lift off and defect) have a different relative phase and amplitude response. By means of Phase rotation and Gain change of the X Y signal components, one of these indications can be manipulated to be almost identical in phase and amplitude as the other and then by subtraction (mixing), the unwanted component is minimized, giving an improved detection of the required signal.
"Auto-Mix" simplifies the sometimes complex procedure of mixing two different frequency signals and can be achieved on the WeldCheck through a series of easy steps. Once set up, the Auto-mix itself is as simple as pressing one key.
"Conductivity Measurement" - When connecting the Conductivity Probe, the WeldCheck auto-detects the probe and seamlessly switches into conductivity mode. Removal of the probe switches the instrument back to flaw detection mode.
"Automatic Lift Off Gain Compensation" automatically compensates the gain of the defect channel according to the paint thickness thus ensuring that a defect signal will appear the same height irrespective of the paint thickness.
Top-Quality Warranties for Top-Quality Instruments
ETher NDE is unique in that they offer warranty coverage unlike anyone else in the field. All ETher Phase Plane Instruments come with the standard 3-year warranty, which covers all components of the instrument and only excludes customer damage or misuse. However, you can also opt in for an extended 6-year ETherCover warranty plan, putting it truly in a league of its own.
The ETherCover 6-Year Extended Warranty Includes:
Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
One Free of Charge Battery Swap within the six year period (if required)
One Free of Charge Keypad Replacement within the six-year period (if required)
Guaranteed Fast Repair
Free of Charge Software Upgrades within the six year period
ETher NDE WeldCheck Specifications
Conductivity Specification (WeldCheck Only)
Standard WeldCheck Series Kits
Optional Accessories
Both the WeldCheck and WeldCheck 2 can perform a great many eddy current inspection tasks due to their superior performance, including weld inspection, surface defect detection and low frequency inspection of non-ferrous material.
The WeldCheck 2 is a single channel/frequency instrument that offers a simplified specification but none the less boasts a 10Hz-20MHz frequency range.
The WeldCheck is a dual channel/frequency instrument with conductivity for maximum flexibility, with a frequency range of 10Hz-12.8MHz.
Features
Single or Dual Channel models
Large, Crisp Daylight Readable Display
User Friendly Interface and Ergonomic Lightweight Design
Industry Standard Probe Connectors
8 Hour Battery Life
Rapid 2.5 Hour Charging Time
Three-Year Warranty (6-Year Extended Warranty with ETherCover)
Advanced Features Loop, Guides and Automatic Lift Off Gain Connection
Lightweight, Rugged and Easy to Use
The WeldCheck weighs just 2.6lbs (1.2kg), has a tough metal outer case and is optimized to resist moist atmospheres. It's 8.5 hour battery life and storage of over 500 readings allows field use for an entire shift without interruption. Additionally, the WeldCheck is equipped with an easy to navigate menu system for rapid function access, including 4 programable, quick access "soft keys" to fit your needs.
Works the Way You Do
The WeldCheck series features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Loop, Guides and Trace Features
"Loop" is a convenient function for capturing live repetitive signals and then optimizing the settings in order to simplify the task of optimizing the parameters.
"Guides" allows the user to display a slide show that can be created easily using 3rd party software. Instructions, tutorials, etc. can be added to the WeldCheck quickly so the inspector can easily switch between the Inspection itself and the Guides while performing a live test.
The "Trace" function allows a reference waveform to be stored on the screen alongside the graticule behind the live spot, allowing the operator to readily compare live data with the reference calibration.
Exclusive Features for WeldCheck Plus
"Dual Frequency / Channel Feature" - At different frequencies, different signal indications (e.g. lift off and defect) have a different relative phase and amplitude response. By means of Phase rotation and Gain change of the X Y signal components, one of these indications can be manipulated to be almost identical in phase and amplitude as the other and then by subtraction (mixing), the unwanted component is minimized, giving an improved detection of the required signal.
"Auto-Mix" simplifies the sometimes complex procedure of mixing two different frequency signals and can be achieved on the WeldCheck through a series of easy steps. Once set up, the Auto-mix itself is as simple as pressing one key.
"Conductivity Measurement" - When connecting the Conductivity Probe, the WeldCheck auto-detects the probe and seamlessly switches into conductivity mode. Removal of the probe switches the instrument back to flaw detection mode.
"Automatic Lift Off Gain Compensation" automatically compensates the gain of the defect channel according to the paint thickness thus ensuring that a defect signal will appear the same height irrespective of the paint thickness.
Top-Quality Warranties for Top-Quality Instruments
ETher NDE is unique in that they offer warranty coverage unlike anyone else in the field. All ETher Phase Plane Instruments come with the standard 3-year warranty, which covers all components of the instrument and only excludes customer damage or misuse. However, you can also opt in for an extended 6-year ETherCover warranty plan, putting it truly in a league of its own.
The ETherCover 6-Year Extended Warranty Includes:
Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
One Free of Charge Battery Swap within the six year period (if required)
One Free of Charge Keypad Replacement within the six-year period (if required)
Guaranteed Fast Repair
Free of Charge Software Upgrades within the six year period
ETher NDE WeldCheck Specifications
| ETher NDE WeldCheck Specifications | ||
| Probe | WeldCheck 2 | WeldCheck |
| Connectors | 12 Way Lemo 2b (Absolute, Bridge and Reflection) and Connection Lemo 00 (for single element absolute probes). | Simulataneous probe operation possile using Lemo 12 way and Lemo 00 |
| Frequency | Single Freq. = 10Hz - 20MHz with range variable resolution | Dual Freq. = 10Hz - 12.8MHz |
| Gain | ||
| Overall | -18 to 100 dB, 0.1, 1 and 6dB steps (100dB maximum) | |
| Input | 0dB or 12dB | |
| Drive | 0dB, 6dB and 10dB (0dB reference 1mW into 50 ohm) | |
| Max X/Y Ratio | /-100.0 dB | |
| Phase | ||
| Range | 0.0-359.9°, 0.1° steps | |
| Auto Phase | Allows phase angle to be automatically set to a pre set angle | |
| Filters | ||
| Normal High Pass | DC to 2kHz or Low Pass Filter, which ever is the lower in 1 Hz steps. Plus variable adaptive balance drift compensation 0.01 - 0.5 Hz (6 steps) | |
| Normal Low Pass | 1Hz to 2kHz or a quarter of the lowest test frequency, which ever is lower in 1 Hz steps | |
| Balance | ||
| Manual | 14 internal balance loads; 2.2μH, 5.0μH, 6.0μH, 6.5μH, 7.0μH, 7.5μH, 8.2μH, 12μH, 15μH, 18μH, 22μH, 30μH, 47μH, 82μH | |
| Automatic | Optimized balance load selection | |
| Alarms | ||
| Box | Fully configurable, Freeze, Tone or visual | |
| Sector | Fully configurable, Freeze, Tone or visual | |
| Output | Open collector transtor (50v dc at 10mA max) available on 12 way lemo | |
| Display | ||
| Type | 5.7” (145mm), 18 bit Color, daylight readable | |
| Viewable Area | 115.2mm (Horizontal) x 86.4mm (Vertical) | |
| Resolution | 640 x 480 pixels | |
| Flip | Manual or automatic screen orrientation change to enable left or right handed use | |
| Color Schemes | User configurable Dark, Bright and Black & White | |
| Configurable Screen | Full Screen, Single, Dual Spot or Dual Pane with variable size and location and function e.g. XY, Timebase, Waterfall and Meter | |
| Display Modes | Spot, Time base (0.1-20 seconds x 1-200 sweeps and up to 55 seconds), Waterfall and Meter with peak hold and % readout | |
| Graticules | None, Grid (4 sizes 5, 10, 15 and 20% FSH), Polar (4 sizes 5, 10, 15 and 20% FSH) | |
| Offset | Spot Position: Y =-50 to 50, X =-65 to 65% | |
| Digital Spot | Display in X,Y or R,θ | |
| Position Readout Summary | Display of all settings in Legacy Format | |
| Removable Data Storage | ||
| Setup Storage | micro SD up to 32GB, holding over 10,000 settings | |
| Stored Screen | micro SD up to 32GB, holding over 10,000 screen shots | |
| Shots | Comprehensive Record Replay and Storage | |
| Record Replay | Real-time recording of trace data and Replay on instruments and desktop PC up to 164 seconds | |
| Outputs | ||
| PC Connectivity | USB (Full PC remote control plus Real Time data) | |
| Digital Volt Free Alarm | On Lemo 12 way Open collector transistor (36v dc at 10mA max). | |
| VGA | Full 15 way VGA output | |
| General | ||
| Languages | English, French, Spanish, Russian, Japanese, Chinese, Turkish | |
| Verification Level | The system includes on delivery a 2 year validity Verification Level 2 detailed functional check and calibration as per ISO 15548-1:2013 | |
| Power on Self Test | The system performs a self test on start up of external ram, sd ram, accelerometer, Micro SD card, LCD screen buffer | |
| Power | ||
| External | 100-240 v 50-60Hz 30 Watts | |
| Battery | Internal 7.2V nominal @ 3100mAh = 22.32 watt.hr | |
| Running Time | Up to 8 hours with a 2MHz Pencil Probe 30% Back Light and up to 6 hours with a Rotary Drive at 3000rpm 50% duty cycle | |
| Charging Time | 2.5 hrs. charge time, Simultaneous charge and operation | |
| Physical | ||
| Weight | 1.2 kg, 2.7 lbs | |
| Size (WxHxD) | 237.5mm x 144mm x 52mm / 9.4” x 5.7” x 2.1” | |
| Material | Aluminum alloy Mg Si 0.5 powder-coated | |
| Operating Temp | -20 to 60 °C | |
| Storage Temp | Storage for up to 12 months -20 to 35 °C Nominal 20 °C | |
| IP Rating | 54 | |
Conductivity Specification (WeldCheck Only)
| WeldCheck Conductivity Specification | |
| Frequency | One frequency only 60kHz standard (choice of 120, 240 and 480kHz) |
| Accuracy | 0.5%-10% IACS better than /-0.05% IACS 10%-25% IACS better than /-0.25% IACS 25%-60% IACS better than /-0.5% IACS 60%-110% IACS better than /-1% IACS Lift Off corrected to 1.0mm No temperature compensation All Errors at 90% Confidence Level |
| Resolution | 3 decimal points max Auto Resolution Mode AutoS = Legacy Instrument, Auto = SigmaCheck |
Standard WeldCheck Series Kits
KIWEL003 Kit, WeldCheck2, Eddy Current Portable Flaw Detector, Including:
- IWEL003 Instrument, WeldCheck2, Single Frequency, (10Hz-12.8MHz) Hand Held, Portable Flaw Detector. Software Manual on USB Stick
- AWEL002 AeroCheck, Power Adapter Input Plugs (UK, EU, US & Australia)
- AWEL003 Adjustable Shoulder Strap, Padded with Quick-Release
- AC006 Instrument Soft Carry Case
- A090 USB Cable, A to MIN B
- 40463 Quick Reference Card
KIWEL002 Kit, WeldCheck , Eddy Current Portable Flaw Detector, Including:
- IWEL002 Instrument, WeldCheck , Dual Frequency, (10Hz-12.8MHz) Hand Held, Portable Flaw Detector. Software Manual on USB Stick
- AWEL002 AeroCheck, Power Adapter Input Plugs (UK, EU, US & Australia)
- AWEL003 Adjustable Shoulder Strap, Padded with Quick-Release
- AC006 Instrument Soft Carry Case
- A090 USB Cable, A to MIN B
- 40463 Quick Reference Card
- ALLCX-M02-015A Lead, Lemo 00 to Microdot, 1.5m (Absolute)
- ALL12-L04-015R Lead, Lemo 12-Way - Lemo 4-Way (Reflection)
Optional Accessories
- AWEL004 Hard Transit Case
- AAER004 Protective Splash Proof Cover (WeldCheck2, WeldCheck , AeroCheck2, AeroCheck )
- AWEL006 External, 8 x AA Battery Holder with On/Off Switch
- AWEL008 In car Power Adapter
- ALL12-L04-015R Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ALL12-L04-015B Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-M02-015A Lead, Lemo 00 to Microdot, 1.5m (Absolute)
- ALLCX-B02-015A Lead. Lemo 00 to BNC, 1.5m (Absolute)
- 40470 Tripod Bracket To fit 1/4” Camera Tripod Mount with Male Screw
The WeldCheck Series of Flaw Detectors appeals to users across a wide range of sectors including Offshore, Rope Access, Infrastructure NDT applications, plus other weld inspection requirements replacing MPI and LPI, especially on coated welds.The WeldCheck2 EC Flaw Detector is single channel, 10Hz- 20MHz, lightweight eddy current flaw detector, housed in a tough aluminium alloy Mg Si 0.5 powder-coated outer case with rubber end bumpers and has been designed with the end user in mind and was developed to meet the requirements on EN1711 & ISO 17643 "Eddy Current Examination of Welds by Complex Phase Analysis"
ETher NDE ETherCheck ET/Bond Testing Flaw Detector - NEW (ETherCheck)
Twice the Functionality in One Instrument
The EtherCheck is a combined Eddy Current and Bond Testing Flaw Detector. It comes with a rich range of features offered by a best in class eddy current flaw detector combined with the most widely used acoustic bond testing method; Pitch-Catch. Features a single frequency range of 10Hz-20MHz and dual range of 10Hz-12.8MHz.
All functions are in a single lightweight instrument with a common user interface between the two modes, resulting in simple operator led set up.
Features
Dual and Single Frequency
Includes General Eddy Current, Rotary, Conductivity and Pitch-Catch
Pitch-Catch dry coupled bond testing mode allows rapid detection of defects in laminate, bonded and sandwich structures
Automatic Test Frequency Optimization
Waveform, Time-base and Phase / Frequency Plots
User Friendly Interface, Single Level Menu System, "Quick Function" Sidebar
Large, Crisp Daylight Readable Display - 5.7" (145mm)
Rugged lightweight housing - 2.6 lbs. (1.2 kg)
Advanced Features Loop, Guides, Trace, Dual Frequency, Auto-Mix
Lightweight, Rugged and Easy to Use
The ETherCheck weighs just 2.6lbs (1.2kg), has a tough metal outer case and is optimized to resist moist atmospheres. It's 8.5 hour battery life and storage of over 500 readings allows field use for an entire shift without interruption. Additionally, the ETherCheck is equipped with an easy to navigate menu system for rapid function access, including 4 programable, quick access "soft keys" to fit your needs.
Works the Way You Do
The ETherCheck series features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Fully Featured Instrument
Loop, Guides, Trace, Rotary Capabilities, Conductivity and More
"Loop" is a convenient function for capturing live repetitive signals and then optimizing the settings in order to simplify the task of optimizing the parameters.
"Guides" allows the user to display a slide show that can be created easily using 3rd party software. Instructions, tutorials, etc. can be added to the ETherCheck quickly so the inspector can easily switch between the Inspection itself and the Guides while performing a live test.
The "Trace" function allows a reference waveform to be stored on the screen alongside the graticule behind the live spot, allowing the operator to readily compare live data with the reference calibration.
Includes "Rotary Capabilities" as standard and can be used with the ETher Mercury (mini) ARD002, Hocking 33A100 or the Rohmann MR3/SR1 and SR2 Drives (with special adapter cable).
The "Dual Frequency" function manipulates one indication to be almost identical in phase and amplitude as the other and then by subtracting (mixing), the unwanted component is minimized, giving an improved detection of the required signal.
"Auto-Mix" simplifies the sometimes complex procedure of mixing two different frequency signals and can be achieved on the ETherCheck through a series of easy steps. Once set up, the Auto-mix itself is as simple as pressing one key.
"Conductivity Mode" - when connecting the Conductivity Probe, the instrument auto-detects the probe and seamlessly switches into conductivity mode. Removal of the probe switches the instrument back to flaw detection mode.
Top-Quality Warranties for Top-Quality Instruments
ETher NDE is unique in that they offer warranty coverage unlike anyone else in the field. All ETher Phase Plane Instruments come with the standard 3-year warranty, which covers all components of the instrument and only excludes customer damage or misuse. However, you can also opt in for an extended 6-year ETherCover warranty plan, putting it truly in a league of its own.
The ETherCover 6-Year Extended Warranty Includes:
Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
One Free of Charge Battery Swap within the six year period (if required)
One Free of Charge Keypad Replacement within the six-year period (if required)
Guaranteed Fast Repair
Free of Charge Software Upgrades within the six year period
ACCESSORIES :
The EtherCheck is a combined Eddy Current and Bond Testing Flaw Detector. It comes with a rich range of features offered by a best in class eddy current flaw detector combined with the most widely used acoustic bond testing method; Pitch-Catch. Features a single frequency range of 10Hz-20MHz and dual range of 10Hz-12.8MHz.
All functions are in a single lightweight instrument with a common user interface between the two modes, resulting in simple operator led set up.
Features
Dual and Single Frequency
Includes General Eddy Current, Rotary, Conductivity and Pitch-Catch
Pitch-Catch dry coupled bond testing mode allows rapid detection of defects in laminate, bonded and sandwich structures
Automatic Test Frequency Optimization
Waveform, Time-base and Phase / Frequency Plots
User Friendly Interface, Single Level Menu System, "Quick Function" Sidebar
Large, Crisp Daylight Readable Display - 5.7" (145mm)
Rugged lightweight housing - 2.6 lbs. (1.2 kg)
Advanced Features Loop, Guides, Trace, Dual Frequency, Auto-Mix
Lightweight, Rugged and Easy to Use
The ETherCheck weighs just 2.6lbs (1.2kg), has a tough metal outer case and is optimized to resist moist atmospheres. It's 8.5 hour battery life and storage of over 500 readings allows field use for an entire shift without interruption. Additionally, the ETherCheck is equipped with an easy to navigate menu system for rapid function access, including 4 programable, quick access "soft keys" to fit your needs.
Works the Way You Do
The ETherCheck series features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Fully Featured Instrument
Loop, Guides, Trace, Rotary Capabilities, Conductivity and More
"Loop" is a convenient function for capturing live repetitive signals and then optimizing the settings in order to simplify the task of optimizing the parameters.
"Guides" allows the user to display a slide show that can be created easily using 3rd party software. Instructions, tutorials, etc. can be added to the ETherCheck quickly so the inspector can easily switch between the Inspection itself and the Guides while performing a live test.
The "Trace" function allows a reference waveform to be stored on the screen alongside the graticule behind the live spot, allowing the operator to readily compare live data with the reference calibration.
Includes "Rotary Capabilities" as standard and can be used with the ETher Mercury (mini) ARD002, Hocking 33A100 or the Rohmann MR3/SR1 and SR2 Drives (with special adapter cable).
The "Dual Frequency" function manipulates one indication to be almost identical in phase and amplitude as the other and then by subtracting (mixing), the unwanted component is minimized, giving an improved detection of the required signal.
"Auto-Mix" simplifies the sometimes complex procedure of mixing two different frequency signals and can be achieved on the ETherCheck through a series of easy steps. Once set up, the Auto-mix itself is as simple as pressing one key.
"Conductivity Mode" - when connecting the Conductivity Probe, the instrument auto-detects the probe and seamlessly switches into conductivity mode. Removal of the probe switches the instrument back to flaw detection mode.
Top-Quality Warranties for Top-Quality Instruments
ETher NDE is unique in that they offer warranty coverage unlike anyone else in the field. All ETher Phase Plane Instruments come with the standard 3-year warranty, which covers all components of the instrument and only excludes customer damage or misuse. However, you can also opt in for an extended 6-year ETherCover warranty plan, putting it truly in a league of its own.
The ETherCover 6-Year Extended Warranty Includes:
Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
One Free of Charge Battery Swap within the six year period (if required)
One Free of Charge Keypad Replacement within the six-year period (if required)
Guaranteed Fast Repair
Free of Charge Software Upgrades within the six year period
| ETher NDE ETherCheck Specifications | |
| Probe | |
| Connectors | 12 Way Lemo 2b (Absolute, Bridge and Reflection) and Connection Lemo 00 (for single element absolute probes). Simultaneous probe operation possible using Lemo 12 way and Lemo 00 |
| Rotary | 600-3000 rpm - ETher Rotary Drive (ARD002), Hocking 33A100, Rohmann MR3, SR1 and SR2 Drive (special adapter required) |
| Frequency | Single Freq. = 10Hz – 20MHz with range variable resolution. Dual Freq. = 10Hz - 12.8MHz & Mix -18 to 18dB on output |
| Gain | |
| Overall | -18 to 104dB, 0.1, 1 and 6dB steps (104dB maximum) |
| Input | 0dB or 12dB |
| Drive | 0dB, 6dB and 10dB (0dB reference 1mW into 50 ohm) |
| Max X/Y Ratio | /-100.0 dB |
| Phase | |
| Range | 0.0-359.9°, 0.1° steps |
| Auto Phase | Allows phase angle to be automatically set to a pre-set angle |
| Filters | |
| Normal High Pass | DC to 2kHz or Low Pass Filter, which ever is the lower in 1Hz steps. Plus variable adaptive balance drift compensation 0.01 - 0.5Hz (6 steps) |
| Normal Low Pass | 1Hz to 2kHz or a quarter of the lowest test frequency, which ever is lower in 1Hz steps |
| Balance | |
| Manual | 14 internal balance loads; 2.2μH, 5.0μH, 6.0μH, 6.5μH, 7.0μH, 7.5μH, 8.2μH, 12μH, 15μH, 18μH, 22μH, 30μH, 47μH, 82μH |
| Automatic | Optimized balance load selection |
| Alarms | |
| Box | Fully configurable, Freeze, Tone or Visual |
| Sector | Fully configurable, Freeze, Tone or Visual |
| Output | Open collector transistor (32v dc at 10mA max) available on 12 way lemo |
| Display | |
| Type | 5.7” (145mm), 18 bit Color, daylight readable |
| Viewable Area | 115.2mm (Horizontal) x 86.4mm (Vertical) |
| Resolution | 640 x 480 pixels |
| Flip | Manual or automatic screen orrientation change to enable left or right handed use |
| Color Schemes | User configurable Dark, Bright and Black & White |
| Configurable Screen | Full Screen, Single, Dual Spot or Dual Pane with variable size and location and function e.g. XY, Timebase, Waterfall and Meter |
| Display Modes | Spot, Time base (0.1-20 seconds x 1-200 sweeps and up to 55 seconds), Waterfall and Meter with peak hold and % readout |
| Graticules | None, Grid (4 sizes 5, 10, 15 and 20% FSH), Polar (4 sizes 5, 10, 15 and 20% FSH) |
| Offset | Spot Position: Y =-50 to 50, X =-65 to 65% |
| Digital Spot | Display in X,Y or R,θ |
| Position Readout Summary | Display of all settings in Legacy Format |
| Removable Data Storage | |
| Setup Storage | micro SD up to 32GB, holding over 10,000 settings |
| Stored Screen | micro SD up to 32GB, holding over 10,000 screen shots |
| Shots | Comprehensive Record Replay and Storage |
| Record Replay | Up to 164 seconds on instrument and on PC over USB limited by Hard Drive capacity |
| Outputs | |
| PC Connectivity | USB (Full PC remote control plus Real Time data) |
| Digital Volt Free Alarm | On Lemo 12 way Open collector transistor (36v dc at 10mA max) |
| VGA | Full 15 way VGA output |
| General | |
| Languages | English, French, Spanish, Italian, Portuguese, Russian, Japanese, Chinese, Turkish, Czech, Norwegian |
| Verification Level | On delivery, the system includes a 2 year validity Verification Level 2 detailed functional check and calibration as per ISO 15548-1:2013 |
| Power On Self Test | The system performs a self test on start up of external ram, sd ram, accelerometer, Micro SD card, LCD screen buffer |
| Power | |
| External | 100-240 v 50-60Hz 30 Watts |
| Battery | Internal 7.2V nominal @ 3100mAh = 22.32 watt.hr |
| Running Time | Up to 8 hours with a 2MHz Pencil Probe 30% Back Light and up to 6 hours with a Rotary Drive at 3000rpm 50% duty cycle. Up to 6 hours using Pitch-Catch Bond Testing Probe |
| Charging Time | 2.5 hrs. charge time, Simultaneous charge and operation |
| Physical | |
| Weight | 2.7 lbs (1.2 kg) |
| Size (WxHxD) | 9.4” x 5.7” x 2.1” (237.5mm x 144mm x 52mm) |
| Material | Aluminium alloy Mg Si 0.5 powder-coated |
| Operating Temp | -20 to 60 °C |
| Storage Temp | Storage for up to 12 months -20 to 35 °C Nominal 20 °C |
| IP Rating | 54 |
| ETherCheck Conductivity Specification | |
| Frequency | One frequency only 60kHz standard (choice of 120, 240 and 480kHz) |
| Accuracy | 0.5%-10% IACS better than /-0.05% IACS 10%-25% IACS better than /-0.25% IACS 25%-60% IACS better than /-0.5% IACS 60%-110% IACS better than /-1% IACS Lift Off corrected to 1.0mm No temperature compensation All Errors at 90% Confidence Level |
| Resolution | 3 decimal points max Auto Resolution Mode AutoS = Legacy Instrument, Auto = SigmaCheck |
| ETherCheck Bond Testing Specification | |
| Modes | |
| Operating Mode | Bond Testing: Pitch-Catch Tone Burst |
| Display Modes | RF (A-Scan waveform), Impedance Plane (Flying Spot), Frequency Spectrum, Time base Scan*, Encoded Scan* |
| Signal Processing | |
| Main Gain | 0 to 60dB in 1dB steps |
| Rectification | RF, Positive half wave, Negative half wave, Full wave |
| Filtering | Low pass filtering of Amplitude / Phase |
| Pitch-Catch Mode | |
| Waveform Type | Tone burst with fixed or swept frequency |
| Output Voltage | 6, 8, 10, 12, 18, 24, 30, 36V |
| Frequency Range | 1kHz to 100kHz – probe dependent |
| Sample Rate | 440kS/s |
| Time base Range | 100us to 2ms |
| Time base Delay | 0us to 1ms |
| RF mode gates | Adjustable threshold, start and width |
| Y-T mode gates | Multiple alarm regions, sector, box and circle |
| Calibration Mode | Automatic inspection frequency with manual adjustment |
| Bond/Dis-Bond Alarm | Audible and visual alarm on instrument display and probe |
| Pitch-Catch Probe | |
| Operating Frequencies | 30kHz (suitable for 10kHz to 50kHz operation) |
| Specification | |
| Probe Separation | 17mm |
| Linear Travel | >5mm |
| Probe Auto-recognition | Yes, with default inspection settings stored in probe |
| Alarm LED | Yes, follows instrument alarm state |
| Probe tips | Rounded end and flat end, user replaceable |
| Probe housing material | Anodized aluminum, with stainless steel probe housings, rubber grip |
| Connector | 8 pin Lemo |
ACCESSORIES :
- AAER002 Hard Transit Case
- AAER004 Protective Splash Proof Cover (WeldCheck2, WeldCheck , AeroCheck2, AeroCheck , ETherCheck)
- AWEL006 External, 8 x AA Battery Holder with On/Off Switch
- AWEL007 Wrist Strap
- AWEL008 In Car Power Adapter
- 40470 Tripod Bracket to fit 1.4” Camera Tripod Mount with Male Screw
- ARD002 Mercury (mini) Rotary Drive
- ALL12-L04-015R Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ALL12-L04-015B Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALL12-L12-020M Lead to connect Mercury (mini - ARD002) Rotary Drive, 2m. 12-Way Lemo
- ALL12-F08-020ETH Adapter Lead to connect Rohmann Rotary Drive MR3, SR1 and SR2, 2m, 12-Way Lemo
- ALLCX-M02-015A Lead, Lemo 00 to Microdot, 1.5m (Absolute)
- ALLCX-B02-015A Lead, Lemo 00 to BNC, 1.5m (Absolute)
EtherCheck offers the operator a rich range of features combined with the most widely used acoustic bond testing method; Pitch-Catch. A common user interface between the two modes, resulting in simple operator led set up.The EtherCheck is a combined Eddy Current and Bond Testing Flaw Detector. It comes with a rich range of features offered by a best in class eddy current flaw detector combined with the most widely used acoustic bond testing method; Pitch-Catch. Features a single frequency range of 10Hz-20MHz and dual range of 10Hz-12.8MHz.
Ether NDE AeroCheck Plus Dual Frequency Eddy Current Flaw Detector - NEW (AeroCheck Plus)
Designed specifically for Non Destructive Testing n the Aerospace industry, the AeroCheck offers NDT inspectors a lightweight, easy to use solution for NDT inspection.
ETher NDE AeroCheck Specifications :
Optional Accessories :
The AeroCheck is fitted with industry standard 12-Way Lemo connectors and Co-axial Lemo 00 connectors meaning that it can be used with absolute, bridge and reflection probes without the need for adaptors. Furthermore, the AeroCheck has rotary capabilities as standard and can be used with the ETher Mercury, Hocking 33A100, and Rohmann MR3 Drive.
The AeroCheck can be used continuously for up to ten hours with a pencil probe and seven hours with the rotary drive and probe attached.
With a fully daylight readable 5.7″ LCD Colour Full VGA (640 x 480 pixels) screen and weighing just 1.2kg and housed in a tough Aluminium/Mg Si 0.5 Alloy powder-coated outer case, the AeroCheck is ideal for any working environment from the laboratory to the tightest space on an aircraft.
Features:
- Advanced features including Conductivity, Dual Frequency with Auto-mix, Loop, Guides and Trace
- Large, crisp, daylight readable display
- User friendly interface and ergonomic lightweight design
- Rotary Drive Capabilities as Standard
- Industry standard probe connectors
- 8-hour battery life
- Rapid 2.5 Hour charging time
- 3-Year Standard Warranty (6-Year Extended Warranty with ETherCover)
Lightweight, Rugged and Easy to Use
Lightweight at 2.6 lbs. (1.2 kg) and housed in a rugged metal casing, the AeroCheck offers up to eight hours battery life. The large "soft keys" and easy-to-navigate menu systems provide a very user-friendly interface. Additionally, the AeroCheck features a "single-level" menu system, and any menu item can be added to the "Quick Menu" sidebar for easy access during the inspection process.
Works the Way You Do
The AeroCheck series features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Loop, Guides and Trace Features
"Loop" is a convenient function for capturing live repetitive signals and then optimizing the settings in order to simplify the task of optimizing the parameters.
"Guides" allows the user to display a slide show that can be created easily using 3rd party software. Instructions, tutorials, etc. can be added to the AeroCheck quickly so the inspector can easily switch between the Inspection itself and the Guides while performing a live test.
The "Trace" function allows a reference waveform to be stored on the screen alongside the graticule behind the live spot, allowing the operator to readily compare live data with the reference calibration.
The ETherCover 6-Year Extended Warranty Includes:
- Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
- One Free of Charge Battery Swap within the six year period (if required)
- One Free of Charge Keypad Replacement within the six-year period (if required)
- Guaranteed Fast Repair
- Free of Charge Software Upgrades within the six year period
ETher NDE AeroCheck Specifications :
| ETher NDE AeroCheck Specifications | ||
| Probe | AeroCheck 2 | AeroCheck Plus |
| Connectors | 12 Way Lemo 2b (Absolute, Bridge and Refection) and Connection Lemo 00 (for single element absolute probes) | Simultaneous probe operation possible using Lemo 12 way and Lemo 00 |
| Rotary | 600-3000 rpm - ETher Mercury Drive (ADR002), Hocking 33A100, Rohmann MR3, SR1 and SR2 Drive (special adapter needed) | |
| Frequency | Single Freq. = 10Hz – 20MHz with range variable resolution | Dual Freq. = 10Hz - 12.8MHz |
| Gain | ||
| Overall | -18 to 100 dB, 0.1, 1 and 6dB steps (100dB maximum) | |
| Input | 0dB or 12dB | |
| Drive | 0dB, 6dB and 10dB (0dB reference 1mW into 50 ohm) | |
| Max X/Y Ratio | /-100.0 dB | |
| Phase | ||
| Range | 0.0-359.9°, 0.1° steps | |
| Auto Phase | Allows phase angle to be automatically set to a pre set angle | |
| Filters | ||
| Normal High Pass | DC to 2kHz or Low Pass Filter, which ever is the lower in 1 Hz steps. Plus variable adaptive balance drift compensation 0.01 - 0.5 Hz (6 steps) | |
| Normal Low Pass | 1Hz to 2kHz or a quarter of the lowest test frequency, which ever is lower in 1 Hz steps | |
| Balance | ||
| Manual | 14 internal balance loads; 2.2µH, 5.0µH, 6.0µH, 6.5µH, 7.0µH, 7.5µH, 8.2µH, 12µH, 15µH, 18µH, 22µH, 30µH, 47µH, 82µH | |
| Automatic | Optimized balance load selection | |
| Alarms | ||
| Box | Fully configurable, Freeze, Tone or visual | |
| Sector | Fully configurable, Freeze, Tone or visual | |
| Output | Open collector transtor (50v dc at 10mA max) available on 12 way Lemo | |
| Display | ||
| Type | 5.7” (145mm), 18 bit Color, daylight readable | |
| Viewable Area | 115.2mm (Horizontal) x 86.4mm (Vertical) | |
| Resolution | 640 x 480 pixels | |
| Flip | Manual or automatic screen orientation change to enable left or right handed use | |
| Color Schemes | User configurable Dark, Bright and Black & White | |
| Configurable Screen | Full Screen, Single, Dual Spot or Dual Pane with variable size and location and function e.g. XY, Timebase, Waterfall and Meter | |
| Display Modes | Spot, Time base (0.1-20 seconds x 1-200 sweeps and up to 55 seconds), Waterfall and Meter with peak hold and % readout | |
| Graticules | None, Grid (4 sizes 5, 10, 15 and 20% FSH), Polar (4 sizes 5, 10, 15 and 20% FSH) | |
| Offset | Spot Position: Y =-50 to 50, X =-65 to 65% | |
| Digital Spot | Display in X,Y or R,θ | |
| Position Readout Summary | Display of all settings in Legacy Format | |
| Removable Data Storage | ||
| Setup Storage | micro SD up to 32GB, holding over 10,000 settings | |
| Stored Screen | micro SD up to 32GB, holding over 10,000 screen shots | |
| Shots | Comprehensive Record Replay and Storage | |
| Record Replay | Real-time recording of trace data and Replay on instruments and desktop PC up to 164 seconds | |
| Outputs | ||
| PC Connectivity | USB (Full PC remote control plus Real Time data) | |
| Digital volt free alarm | On Lemo 12 way Open collector transistor (36v dc at 10mA max) | |
| VGA | Full 15 way VGA output | |
| General | ||
| Languages | English, French, Spanish, Russian, Japanese, Chinese, Turkish | |
| Verification Level | The system includes on delivery a 2 year validity Verification Level 2 detailed functional check and calibration as per ISO 15548-1:2013 | |
| Power on Self Test | The system performs a self test on start up of external ram, sd ram, accelerometer, Micro SD card, LCD screen buffer | |
| Power | ||
| External | 100-240 v 50-60Hz 30 Watts | |
| Battery | Internal 7.2V nominal @ 3100mAh = 22.32 watt.hr | |
| Running Time | Up to 8 hours with a 2MHz Pencil Probe 30% Back Light and up to 6 hours with a Rotary Drive at 3000rpm 50% duty cycle | |
| Charging Time | 2.5 hrs. charge time, Simultaneous charge and operation | |
| Physical | ||
| Weight | 2.7 lbs (1.2 kg) | |
| Size (WxHxD) | 9.4” x 5.7” x 2.1” (237.5mm x 144mm x 52mm) | |
| Material | Aluminum alloy Mg Si 0.5 powder-coated | |
| Operating Temp | -20 to 60 °C | |
| Storage Temp | Storage for up to 12 months -20 to 35 °C Nominal 20 °C | |
| IP Rating | 54 | |
Optional Accessories :
- AAER002 Hard Transit Case
- AAER004 Protective Splash Proof Cover (WeldCheck2, WeldCheck , AeroCheck 2, AeroCheck )
- AWEL006 External, 8 x AA Battery Holder with On/Of Switch
- AWEL008 In car Power Adapter
- ALL12-L04-015R Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ALL12-L04-015B Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-M02-015A Lead, Lemo 00 to Microdot, 1.5m (Absolute)
- ALLCX-B02-015A Lead, Lemo 00 to BNC, 1.5m (Absolute)
- ARD002 Mercury (mini) Rotary Drive
- ALL12-L12-020M Lead to connect Mercury (mini - ARD002) Rotary Drive, Lemo 12-Way, 2m
- ALL12-F08-020ETH Adapter, lead to connect Rohmann Rotary Drive MR3, SR1 and SR2, Lemo 12-Way, 2m.
- 40470 Tripod Bracket To fit 1/4” Camera Tripod Mount with Male Screw
The AeroCheck offers the end user dual frequency capability, with an excellent Frequency Range from 10Hz to 12.8MHz, with Rotary Drive Capabilities as standard, but in addition offers Auto-mix and Conductivity Measurement.The AeroCheck Series can be used with all reflection, bridge and absolute probes from all manufacturers and uses industry standard 12-Way Lemo and Co-axial Lemo 00 connectors, reducing the need to use adapters.
Ether NDE AeroCheck 2 Single Frequency Eddy Current Flaw Detector - NEW (AeroCheck 2)
Designed specifically for Non Destructive Testing n the Aerospace industry, the AeroCheck offers NDT inspectors a lightweight, easy to use solution for NDT inspection.
ETher NDE AeroCheck Specifications :
Optional Accessories :
The AeroCheck is fitted with industry standard 12-Way Lemo connectors and Co-axial Lemo 00 connectors meaning that it can be used with absolute, bridge and reflection probes without the need for adaptors. Furthermore, the AeroCheck has rotary capabilities as standard and can be used with the ETher Mercury, Hocking 33A100, and Rohmann MR3 Drive.
The AeroCheck can be used continuously for up to ten hours with a pencil probe and seven hours with the rotary drive and probe attached.
With a fully daylight readable 5.7″ LCD Colour Full VGA (640 x 480 pixels) screen and weighing just 1.2kg and housed in a tough Aluminium/Mg Si 0.5 Alloy powder-coated outer case, the AeroCheck is ideal for any working environment from the laboratory to the tightest space on an aircraft.
Features:
- Advanced features including Conductivity, Dual Frequency with Auto-mix, Loop, Guides and Trace
- Large, crisp, daylight readable display
- User friendly interface and ergonomic lightweight design
- Rotary Drive Capabilities as Standard
- Industry standard probe connectors
- 8-hour battery life
- Rapid 2.5 Hour charging time
- 3-Year Standard Warranty (6-Year Extended Warranty with ETherCover)
Lightweight, Rugged and Easy to Use
Lightweight at 2.6 lbs. (1.2 kg) and housed in a rugged metal casing, the AeroCheck offers up to eight hours battery life. The large "soft keys" and easy-to-navigate menu systems provide a very user-friendly interface. Additionally, the AeroCheck features a "single-level" menu system, and any menu item can be added to the "Quick Menu" sidebar for easy access during the inspection process.
Works the Way You Do
The AeroCheck series features a daylight-readable 5.7” LCD Color Full VGA (640 x 480 pixels) screen, ensuring the operator has excellent signal resolution and presentation no matter what the working conditions are. With the built-in “flip” function, it works equally well for left or right-handed users.
Loop, Guides and Trace Features
"Loop" is a convenient function for capturing live repetitive signals and then optimizing the settings in order to simplify the task of optimizing the parameters.
"Guides" allows the user to display a slide show that can be created easily using 3rd party software. Instructions, tutorials, etc. can be added to the AeroCheck quickly so the inspector can easily switch between the Inspection itself and the Guides while performing a live test.
The "Trace" function allows a reference waveform to be stored on the screen alongside the graticule behind the live spot, allowing the operator to readily compare live data with the reference calibration.
The ETherCover 6-Year Extended Warranty Includes:
- Free of Charge Annual Re-calibration and Health Check for five years commencing at the end of year one
- One Free of Charge Battery Swap within the six year period (if required)
- One Free of Charge Keypad Replacement within the six-year period (if required)
- Guaranteed Fast Repair
- Free of Charge Software Upgrades within the six year period
ETher NDE AeroCheck Specifications :
| ETher NDE AeroCheck Specifications | ||
| Probe | AeroCheck 2 | AeroCheck Plus |
| Connectors | 12 Way Lemo 2b (Absolute, Bridge and Refection) and Connection Lemo 00 (for single element absolute probes) | Simultaneous probe operation possible using Lemo 12 way and Lemo 00 |
| Rotary | 600-3000 rpm - ETher Mercury Drive (ADR002), Hocking 33A100, Rohmann MR3, SR1 and SR2 Drive (special adapter needed) | |
| Frequency | Single Freq. = 10Hz – 20MHz with range variable resolution | Dual Freq. = 10Hz - 12.8MHz |
| Gain | ||
| Overall | -18 to 100 dB, 0.1, 1 and 6dB steps (100dB maximum) | |
| Input | 0dB or 12dB | |
| Drive | 0dB, 6dB and 10dB (0dB reference 1mW into 50 ohm) | |
| Max X/Y Ratio | /-100.0 dB | |
| Phase | ||
| Range | 0.0-359.9°, 0.1° steps | |
| Auto Phase | Allows phase angle to be automatically set to a pre set angle | |
| Filters | ||
| Normal High Pass | DC to 2kHz or Low Pass Filter, which ever is the lower in 1 Hz steps. Plus variable adaptive balance drift compensation 0.01 - 0.5 Hz (6 steps) | |
| Normal Low Pass | 1Hz to 2kHz or a quarter of the lowest test frequency, which ever is lower in 1 Hz steps | |
| Balance | ||
| Manual | 14 internal balance loads; 2.2µH, 5.0µH, 6.0µH, 6.5µH, 7.0µH, 7.5µH, 8.2µH, 12µH, 15µH, 18µH, 22µH, 30µH, 47µH, 82µH | |
| Automatic | Optimized balance load selection | |
| Alarms | ||
| Box | Fully configurable, Freeze, Tone or visual | |
| Sector | Fully configurable, Freeze, Tone or visual | |
| Output | Open collector transtor (50v dc at 10mA max) available on 12 way Lemo | |
| Display | ||
| Type | 5.7” (145mm), 18 bit Color, daylight readable | |
| Viewable Area | 115.2mm (Horizontal) x 86.4mm (Vertical) | |
| Resolution | 640 x 480 pixels | |
| Flip | Manual or automatic screen orientation change to enable left or right handed use | |
| Color Schemes | User configurable Dark, Bright and Black & White | |
| Configurable Screen | Full Screen, Single, Dual Spot or Dual Pane with variable size and location and function e.g. XY, Timebase, Waterfall and Meter | |
| Display Modes | Spot, Time base (0.1-20 seconds x 1-200 sweeps and up to 55 seconds), Waterfall and Meter with peak hold and % readout | |
| Graticules | None, Grid (4 sizes 5, 10, 15 and 20% FSH), Polar (4 sizes 5, 10, 15 and 20% FSH) | |
| Offset | Spot Position: Y =-50 to 50, X =-65 to 65% | |
| Digital Spot | Display in X,Y or R,θ | |
| Position Readout Summary | Display of all settings in Legacy Format | |
| Removable Data Storage | ||
| Setup Storage | micro SD up to 32GB, holding over 10,000 settings | |
| Stored Screen | micro SD up to 32GB, holding over 10,000 screen shots | |
| Shots | Comprehensive Record Replay and Storage | |
| Record Replay | Real-time recording of trace data and Replay on instruments and desktop PC up to 164 seconds | |
| Outputs | ||
| PC Connectivity | USB (Full PC remote control plus Real Time data) | |
| Digital volt free alarm | On Lemo 12 way Open collector transistor (36v dc at 10mA max) | |
| VGA | Full 15 way VGA output | |
| General | ||
| Languages | English, French, Spanish, Russian, Japanese, Chinese, Turkish | |
| Verification Level | The system includes on delivery a 2 year validity Verification Level 2 detailed functional check and calibration as per ISO 15548-1:2013 | |
| Power on Self Test | The system performs a self test on start up of external ram, sd ram, accelerometer, Micro SD card, LCD screen buffer | |
| Power | ||
| External | 100-240 v 50-60Hz 30 Watts | |
| Battery | Internal 7.2V nominal @ 3100mAh = 22.32 watt.hr | |
| Running Time | Up to 8 hours with a 2MHz Pencil Probe 30% Back Light and up to 6 hours with a Rotary Drive at 3000rpm 50% duty cycle | |
| Charging Time | 2.5 hrs. charge time, Simultaneous charge and operation | |
| Physical | ||
| Weight | 2.7 lbs (1.2 kg) | |
| Size (WxHxD) | 9.4” x 5.7” x 2.1” (237.5mm x 144mm x 52mm) | |
| Material | Aluminum alloy Mg Si 0.5 powder-coated | |
| Operating Temp | -20 to 60 °C | |
| Storage Temp | Storage for up to 12 months -20 to 35 °C Nominal 20 °C | |
| IP Rating | 54 | |
Optional Accessories :
- AAER002 Hard Transit Case
- AAER004 Protective Splash Proof Cover (WeldCheck2, WeldCheck , AeroCheck 2, AeroCheck )
- AWEL006 External, 8 x AA Battery Holder with On/Of Switch
- AWEL008 In car Power Adapter
- ALL12-L04-015R Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)
- ALL12-L04-015B Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)
- ALLCX-M02-015A Lead, Lemo 00 to Microdot, 1.5m (Absolute)
- ALLCX-B02-015A Lead, Lemo 00 to BNC, 1.5m (Absolute)
- ARD002 Mercury (mini) Rotary Drive
- ALL12-L12-020M Lead to connect Mercury (mini - ARD002) Rotary Drive, Lemo 12-Way, 2m
- ALL12-F08-020ETH Adapter, lead to connect Rohmann Rotary Drive MR3, SR1 and SR2, Lemo 12-Way, 2m.
- 40470 Tripod Bracket To fit 1/4” Camera Tripod Mount with Male Screw
The AeroCheck 2 is the single frequency EC flaw detector, 10Hz-20MHz, offering all the advanced features, including Loop, Guides and Trace, plus Rotary, but without Conductivity capability.
- 1